[PATCH 1/2] ARM: dts: at91: sama7g5ek: use proper slew-rate settings for GMACs
flat view
STALE1835d
LANDED
From: Claudiu Beznea <hidden>
Date: 2021-09-15 07:49:14
Also in:
linux-devicetree, lkml
Subsystem:
the rest · Maintainer:
Linus Torvalds
Landed in mainline as 968f6e9d51e2 on 2021-10-04.
Datasheet chapter "EMAC Timings" specifies that while in 3.3V domain
GMAC's MDIO pins should be configured with slew-rate enabled, while the
data + signaling pins should be configured with slew-rate disabled when
GMAC works in RGMII or RMII modes. The pin controller for SAMA7G5 sets
the slew-rate as enabled for all pins. Adapt the device tree to comply
with these.
Fixes: 7540629e2fc7 ("ARM: dts: at91: add sama7g5 SoC DT and sama7g5-ek")
Signed-off-by: Claudiu Beznea <redacted>
---
arch/arm/boot/dts/at91-sama7g5ek.dts | 28 ++++++++++++++++++++++------
1 file changed, 22 insertions(+), 6 deletions(-)
diff --git a/arch/arm/boot/dts/at91-sama7g5ek.dts b/arch/arm/boot/dts/at91-sama7g5ek.dts
index 8b13b031a167..0bed8207d498 100644
--- a/arch/arm/boot/dts/at91-sama7g5ek.dts
+++ b/arch/arm/boot/dts/at91-sama7g5ek.dts@@ -353,7 +353,10 @@ &gmac0 { #address-cells = <1>; #size-cells = <0>; pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_gmac0_default &pinctrl_gmac0_txck_default &pinctrl_gmac0_phy_irq>; + pinctrl-0 = <&pinctrl_gmac0_default + &pinctrl_gmac0_mdio_default + &pinctrl_gmac0_txck_default + &pinctrl_gmac0_phy_irq>; phy-mode = "rgmii-id"; status = "okay";
@@ -368,7 +371,9 @@ &gmac1 { #address-cells = <1>; #size-cells = <0>; pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_gmac1_default &pinctrl_gmac1_phy_irq>; + pinctrl-0 = <&pinctrl_gmac1_default + &pinctrl_gmac1_mdio_default + &pinctrl_gmac1_phy_irq>; phy-mode = "rmii"; status = "okay";
@@ -423,14 +428,20 @@ pinctrl_gmac0_default: gmac0_default { <PIN_PA15__G0_TXEN>, <PIN_PA30__G0_RXCK>, <PIN_PA18__G0_RXDV>, - <PIN_PA22__G0_MDC>, - <PIN_PA23__G0_MDIO>, <PIN_PA25__G0_125CK>; + slew-rate = <0>; + bias-disable; + }; + + pinctrl_gmac0_mdio_default: gmac0_mdio_default { + pinmux = <PIN_PA22__G0_MDC>, + <PIN_PA23__G0_MDIO>; bias-disable; }; pinctrl_gmac0_txck_default: gmac0_txck_default { pinmux = <PIN_PA24__G0_TXCK>; + slew-rate = <0>; bias-pull-up; };
@@ -447,8 +458,13 @@ pinctrl_gmac1_default: gmac1_default { <PIN_PD25__G1_RX0>, <PIN_PD26__G1_RX1>, <PIN_PD27__G1_RXER>, - <PIN_PD24__G1_RXDV>, - <PIN_PD28__G1_MDC>, + <PIN_PD24__G1_RXDV>; + slew-rate = <0>; + bias-disable; + }; + + pinctrl_gmac1_mdio_default: gmac1_mdio_default { + pinmux = <PIN_PD28__G1_MDC>, <PIN_PD29__G1_MDIO>; bias-disable; };
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel