Re: [PATCH v3 7/7] arm64: dts: exynos: Add Exynos850 SoC support
From: Sam Protsenko <semen.protsenko@linaro.org>
Date: 2021-08-12 17:42:58
Also in:
linux-devicetree, linux-gpio, linux-samsung-soc, linux-serial, lkml
On Thu, 12 Aug 2021 at 11:17, Krzysztof Kozlowski [off-list ref] wrote:
On 11/08/2021 13:48, Sam Protsenko wrote:quoted
Samsung Exynos850 is ARMv8-based mobile-oriented SoC. This patch adds minimal SoC support by including next Device Tree nodes: 1. Octa cores (Cortex-A55), supporting PSCI v1.0 2. ARM architecture timer (armv8-timer) 3. Interrupt controller (GIC-400) 4. Pinctrl nodes for GPIO 5. Serial node Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> --- Changes in v3: - Used generic fixed clock for serial Changes in v2: * Commit message: - Documented added dts features instead of CPU features * exynos850-usi.dtsi: - Removed, moved everything to exynos850.dtsi * exynos850.dtsi: - Root node: - Added comment about engineering name (Exynos3830) - Renamed pinctrl nodes, adding domain names - Used hard coded IRQ numbers instead of named constants everywhere - Added soc node, moved next nodes there: gic, clock, pinctrls and serial - Used address-cells=1 for soc node and removed unneeded 0x0 from reg properties - Moved exynos850-pinctrl.dtsi include line to the end of exynos850.dtsi - Coding style fixes - cpus: - Used address-cells=1 for cpus node - Renamed cpu@0001 to cpu@1, and so on - Left only "arm,cortex-a55" for cpus compatible - Renamed reg = <0x0001> to <0x1> for cpus - armv8 timer: - Add comment about missing HV timer IRQ to armv8 timer node - Removed not existing properties from armv8 timer node - Fixed cpu number in CPU_MASK() - Removed obsolete clock-frequency property - GIC: - Fixed GIC type to be GIC-400 - Fixed size of GIC's 2nd region to be 0x2000 - serial node: - Hard coded clock number for serial_0 for now; will replace with named const once proper clock driver is implemented - Removed gate_uart_clk0 clock from serial_0, as that clock is not supported in serial driver anyway (yet) - clock node: - Fixed clock controller node name (@0x12.. -> @12..) * exynos850-pinctrl.dtsi: - Referenced pinctrl nodes instead of defining those again in root node - Fixed interrupt-cells (3 -> 2) - Fixed USI related comments for pin config nodes - Removed decon_f_te_* and fm_lna_en nodes (won't be used) - Reordered pin config nodes by pin numbers - Improved all comments - Used existing named constants for pin-function and pin-pud - Fixed node names (used hyphens instead of underscore) - Fixed warnings found in W=1 build .../boot/dts/exynos/exynos850-pinctrl.dtsi | 748 ++++++++++++++++++ arch/arm64/boot/dts/exynos/exynos850.dtsi | 261 ++++++ 2 files changed, 1009 insertions(+) create mode 100644 arch/arm64/boot/dts/exynos/exynos850-pinctrl.dtsi create mode 100644 arch/arm64/boot/dts/exynos/exynos850.dtsidiff --git a/arch/arm64/boot/dts/exynos/exynos850-pinctrl.dtsi b/arch/arm64/boot/dts/exynos/exynos850-pinctrl.dtsi new file mode 100644 index 000000000000..ba5d5f33e2f6 --- /dev/null +++ b/arch/arm64/boot/dts/exynos/exynos850-pinctrl.dtsi@@ -0,0 +1,748 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Samsung's Exynos850 SoC pin-mux and pin-config device tree source + * + * Copyright (C) 2017 Samsung Electronics Co., Ltd. + * Copyright (C) 2021 Linaro Ltd. + * + * Samsung's Exynos850 SoC pin-mux and pin-config options are listed as device + * tree nodes in this file. + */ + +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/pinctrl/samsung.h> + +&pinctrl_alive { + gpa0: gpa0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; + }; + + gpa1: gpa1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; + }; + + gpa2: gpa2 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>; + }; + + gpa3: gpa3 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; + }; + + gpa4: gpa4 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; + }; + + gpq0: gpq0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + /* I2C5 (also called CAM_PMIC_I2C in TRM) */ + i2c5_bus: i2c5-bus { + samsung,pins = "gpa3-5", "gpa3-6"; + samsung,pin-function = <EXYNOS_PIN_FUNC_3>; + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + /* I2C6 (also called MOTOR_I2C in TRM) */ + i2c6_bus: i2c6-bus { + samsung,pins = "gpa3-7", "gpa4-0"; + samsung,pin-function = <EXYNOS_PIN_FUNC_3>; + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + /* USI: UART */ + uart0_bus: uart0-bus { + samsung,pins = "gpq0-0", "gpq0-1"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + }; +}; + +&pinctrl_cmgp { + gpm0: gpm0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; + }; + + gpm1: gpm1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; + }; + + gpm2: gpm2 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; + }; + + gpm3: gpm3 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>; + }; + + gpm4: gpm4 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>; + }; + + gpm5: gpm5 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; + }; + + /* USI_CMGP0: HSI2C function */ + hsi2c3_bus: hsi2c3-bus { + samsung,pins = "gpm0-0", "gpm1-0"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>; + samsung,pin-drv = <0>;There are also macros for DRV.
Unfortunately, existing DRV macros won't work for Exynos850. DRV constants have different meaning for different GPIO domains in Exynos850, so I thought introducing several groups of DRV constants might be confusing. But please let me know if you still want me do that.
I assume you checked whether the actual values of FUNC/PULL/DRV macros match Exynos850 datasheet.
Yep, they are good.
quoted
+ }; + + /* USI_CMGP0: UART function (4 pins, Auto Flow Control) */ + uart1_bus_single: uart1-bus { + samsung,pins = "gpm0-0", "gpm1-0", "gpm2-0", "gpm3-0"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + }; + + /* USI_CMGP0: UART function (2 pins, Non-Auto Flow Control) */ + uart1_bus_dual: uart1-bus-dual { + samsung,pins = "gpm0-0", "gpm1-0"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + }; + + /* USI_CMGP0: SPI function */ + spi1_bus: spi1-bus { + samsung,pins = "gpm0-0", "gpm1-0", "gpm2-0"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + spi1_cs: spi1-cs { + samsung,pins = "gpm3-0"; + samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + spi1_cs_func: spi1-cs-func { + samsung,pins = "gpm3-0"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + /* USI_CMGP1: HSI2C function */ + hsi2c4_bus: hsi2c4-bus { + samsung,pins = "gpm4-0", "gpm5-0"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + /* USI_CMGP1: UART function (4 pins, Auto Flow Control) */ + uart2_bus_single: uart2-bus { + samsung,pins = "gpm4-0", "gpm5-0", "gpm6-0", "gpm7-0"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + }; + + /* USI_CMGP1: UART function (2 pins, Non-Auto Flow Control) */ + uart2_bus_dual: uart2-bus-dual { + samsung,pins = "gpm4-0", "gpm5-0"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + }; + + /* USI_CMGP1: SPI function */ + spi2_bus: spi2-bus { + samsung,pins = "gpm4-0", "gpm5-0", "gpm6-0"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + spi2_cs: spi2-cs { + samsung,pins = "gpm7-0"; + samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + spi2_cs_func: spi2-cs-func { + samsung,pins = "gpm7-0"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; +}; + +&pinctrl_aud { + gpb0: gpb0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpb1: gpb1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + aud_codec_mclk: aud-codec-mclk { + samsung,pins = "gpb0-0"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>; + }; + + aud_codec_mclk_idle: aud-codec-mclk-idle { + samsung,pins = "gpb0-0"; + samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>; + }; + + aud_i2s0_bus: aud-i2s0-bus { + samsung,pins = "gpb0-1", "gpb0-2", "gpb0-3", "gpb0-4"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>; + }; + + aud_i2s0_idle: aud-i2s0-idle { + samsung,pins = "gpb0-1", "gpb0-2", "gpb0-3", "gpb0-4"; + samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>; + }; + + aud_i2s1_bus: aud-i2s1-bus { + samsung,pins = "gpb1-0", "gpb1-1", "gpb1-2", "gpb1-3"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>; + }; + + aud_i2s1_idle: aud-i2s1-idle { + samsung,pins = "gpb1-0", "gpb1-1", "gpb1-2", "gpb1-3"; + samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>; + }; + + aud_fm_bus: aud-fm-bus { + samsung,pins = "gpb1-4"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>; + }; + + aud_fm_idle: aud-fm-idle { + samsung,pins = "gpb1-4"; + samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>; + }; +}; + +&pinctrl_hsi { + gpf2: gpf2 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + sd2_clk: sd2-clk { + samsung,pins = "gpf2-0"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <2>; + }; + + sd2_clk_fast_slew_rate_1x: sd2-clk-fast-slew-rate-1x { + samsung,pins = "gpf2-0"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + sd2_clk_fast_slew_rate_1_5x: sd2-clk-fast-slew-rate-1-5x { + samsung,pins = "gpf2-0"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <1>; + }; + + sd2_clk_fast_slew_rate_2x: sd2-clk-fast-slew-rate-2x { + samsung,pins = "gpf2-0"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <2>; + }; + + sd2_clk_fast_slew_rate_2_5x: sd2-clk-fast-slew-rate-2-5x { + samsung,pins = "gpf2-0"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <3>; + }; + + sd2_clk_fast_slew_rate_3x: sd2-clk-fast-slew-rate-3x { + samsung,pins = "gpf2-0"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <4>; + }; + + sd2_clk_fast_slew_rate_4x: sd2-clk-fast-slew-rate-4x { + samsung,pins = "gpf2-0"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <5>; + }; + + sd2_cmd: sd2-cmd { + samsung,pins = "gpf2-1"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>; + samsung,pin-drv = <2>; + }; + + sd2_bus1: sd2-bus-width1 { + samsung,pins = "gpf2-2"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>; + samsung,pin-drv = <2>; + }; + + sd2_bus4: sd2-bus-width4 { + samsung,pins = "gpf2-3", "gpf2-4", "gpf2-5"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>; + samsung,pin-drv = <2>; + }; + + sd2_pins_as_pdn: sd2-pins-as-pdn { + samsung,pins = "gpf2-0", "gpf2-1", "gpf2-2", "gpf2-3", + "gpf2-4", "gpf2-5"; + samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>; + }; +}; + +&pinctrl_core { + gpf0: gpf0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpf1: gpf1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + sd0_clk: sd0-clk { + samsung,pins = "gpf0-0"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <3>; + }; + + sd0_clk_fast_slew_rate_1x: sd0-clk-fast-slew-rate-1x { + samsung,pins = "gpf0-0"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <1>; + }; + + sd0_clk_fast_slew_rate_2x: sd0-clk-fast-slew-rate-2x { + samsung,pins = "gpf0-0"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <2>; + }; + + sd0_clk_fast_slew_rate_3x: sd0-clk-fast-slew-rate-3x { + samsung,pins = "gpf0-0"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <2>; + }; + + sd0_clk_fast_slew_rate_4x: sd0-clk-fast-slew-rate-4x { + samsung,pins = "gpf0-0"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <3>; + }; + + sd0_cmd: sd0-cmd { + samsung,pins = "gpf0-1"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; + + sd0_rdqs: sd0-rdqs { + samsung,pins = "gpf0-2"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>; + samsung,pin-drv = <3>; + }; + + sd0_nreset: sd0-nreset { + samsung,pins = "gpf0-3"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; + + sd0_bus1: sd0-bus-width1 { + samsung,pins = "gpf1-0"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; + + sd0_bus4: sd0-bus-width4 { + samsung,pins = "gpf1-1", "gpf1-2", "gpf1-3"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; + + sd0_bus8: sd0-bus-width8 { + samsung,pins = "gpf1-4", "gpf1-5", "gpf1-6", "gpf1-7"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; +}; + +&pinctrl_peri { + gpg0: gpg0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpp0: gpp0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + gpp1: gpp1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpp2: gpp2 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpg1: gpg1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpg2: gpg2 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpg3: gpg3 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpc0: gpc0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpc1: gpc1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + /* USI: HSI2C0 */ + hsi2c0_bus: hsi2c0-bus { + samsung,pins = "gpc1-0", "gpc1-1"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + /* USI: HSI2C1 */ + hsi2c1_bus: hsi2c1-bus { + samsung,pins = "gpc1-2", "gpc1-3"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + /* USI: HSI2C2 */ + hsi2c2_bus: hsi2c2-bus { + samsung,pins = "gpc1-4", "gpc1-5"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + /* USI: SPI */ + spi0_bus: spi0-bus { + samsung,pins = "gpp2-0", "gpp2-2", "gpp2-3"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + spi0_cs: spi0-cs { + samsung,pins = "gpp2-1"; + samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + spi0_cs_func: spi0-cs-func { + samsung,pins = "gpp2-1"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + i2c0_bus: i2c0-bus { + samsung,pins = "gpp0-0", "gpp0-1"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + i2c1_bus: i2c1-bus { + samsung,pins = "gpp0-2", "gpp0-3"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c2_bus: i2c2-bus { + samsung,pins = "gpp0-4", "gpp0-5"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c3_bus: i2c3-bus { + samsung,pins = "gpp1-0", "gpp1-1"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c4_bus: i2c4-bus { + samsung,pins = "gpp1-2", "gpp1-3"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + sensor_mclk0_in: sensor-mclk0-in { + samsung,pins = "gpc0-0";All these gpc0 go before hsi2c0_bus node (to have them ordered by datasheet pin name).
Done.
quoted
+ samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <2>; + }; +Rest looks good but anyway will wait for the board DTS. :)
Sure. I'll probably send next patch series only when the board gets announced, and will include board's dts of course.
Best regards, Krzysztof
_______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel