[PATCH v3 01/13] dt-bindings: usb: mtu3: remove support VBUS detection of extcon
From: Chunfeng Yun <chunfeng.yun@mediatek.com>
Date: 2021-07-15 09:08:19
Also in:
linux-devicetree, linux-mediatek, linux-usb, lkml
Subsystem:
mediatek usb3 drd ip driver, open firmware and flattened device tree bindings, the rest, usb subsystem · Maintainers:
Chunfeng Yun, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Linus Torvalds, Greg Kroah-Hartman
Due to no platforms use a multi-funtion pin to detect VBUS status until now when support dual role mode, prefer not to support it anymore; Another reason is that the controller doesn't support idle status, the dual role port works as device or as host, using an IDDIG pin is good enough, this will help to save another multi-function pin; And fix a typo of 'neede'; Last modify example using VBUS to turn on/off device, for device only mode, the driver doesn't get extcon. Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> --- v3: add Acked-by Rob v2: no changes --- .../bindings/usb/mediatek,mtu3.yaml | 22 +++++++++++++++---- 1 file changed, 18 insertions(+), 4 deletions(-)
diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml b/Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml
index dbc7876e0a0b..2cac7a87ce36 100644
--- a/Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml
+++ b/Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml@@ -106,7 +106,7 @@ properties: extcon: deprecated: true description: | - Phandle to the extcon device detecting the IDDIG/VBUS state, neede + Phandle to the extcon device detecting the IDDIG state, needed when supports dual-role mode. It's considered valid for compatibility reasons, not allowed for new bindings, and use "usb-role-switch" property instead.
@@ -230,7 +230,7 @@ examples: }; }; - # Enable/disable device by an input gpio for VBUS pin + # Dual role switch by gpio-usb-b-connector - | #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/power/mt2712-power.h>
@@ -244,13 +244,27 @@ examples: power-domains = <&scpsys MT2712_POWER_DOMAIN_USB2>; clocks = <&topckgen CLK_TOP_USB30_SEL>; clock-names = "sys_ck"; - dr_mode = "peripheral"; + dr_mode = "otg"; usb-role-switch; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + host0: usb@11270000 { + compatible = "mediatek,mt2712-xhci", "mediatek,mtk-xhci"; + reg = <0x11270000 0x1000>; + reg-names = "mac"; + interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT2712_POWER_DOMAIN_USB>; + clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>; + clock-names = "sys_ck", "ref_ck"; + }; connector { compatible = "gpio-usb-b-connector", "usb-b-connector"; type = "micro"; - vbus-gpios = <&pio 13 GPIO_ACTIVE_HIGH>; + id-gpios = <&pio 12 GPIO_ACTIVE_HIGH>; + vbus-supply = <&usb_p0_vbus>; }; };
--
2.18.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel