Re: [PATCH 2/2] arm64: allow TCR_EL1.TBID0 to be configured

On Wed, Nov 25, 2020 at 6:38 AM Szabolcs Nagy [off-list ref] wrote:

The 11/24/2020 11:18, Peter Collingbourne wrote:

quoted

On Tue, Nov 24, 2020 at 10:47 AM Catalin Marinas
[off-list ref] wrote:

quoted

On Sat, Nov 21, 2020 at 01:59:03AM -0800, Peter Collingbourne wrote:

quoted

Introduce a Kconfig option that controls whether TCR_EL1.TBID0 is
set at boot time.

Setting TCR_EL1.TBID0 increases the number of signature bits used by
the pointer authentication instructions for instruction addresses by 8,
which improves the security of pointer authentication, but it also has
the consequence of changing the operation of the branch instructions
so that they no longer ignore the top byte of the target address but
instead fault if they are non-zero. Since this is a change to the
userspace ABI the option defaults to off.

Signed-off-by: Peter Collingbourne <redacted>
Link: https://linux-review.googlesource.com/id/Ife724ad708142bc475f42e8c1d9609124994bbbd
---
This is more of an RFC. An open question is how to expose this.
Having it be a build-time flag is probably the simplest option
but I guess it could also be a boot flag. Since it involves an
ABI change we may also want a prctl() so that userspace can
figure out which mode it is in.

I think we should try to avoid it being a per-task property
so that we don't need to swap yet another system register on
task switch.

Having it changed per task at run-time is problematic as this bit may be
cached in the TLB, so it would require a synchronisation across all CPUs
followed by TLBI. It's not even clear to me from the ARM ARM whether
this bit is tagged by ASID, which, if not, would make a per-process
setting impossible.

So this leaves us with a cmdline option. If we are confident that no
software makes use of tagged instruction pointers, we could have it
default on.

I would be concerned about turning it on by default because tagged
instruction pointers may end up being used unintentionally as a result
of emergent behavior. For example, when booting Android under FVP with
this enabled I discovered that SwiftShader would crash when entering
JITed code because the code was being stored at a tagged address
(tagged because it had been allocated using Scudo's MTE allocator).
Arguably software shouldn't be storing executable code in memory owned
by the allocator as this would require changing the permissions of
memory that it doesn't own, but from the kernel's perspective it is
valid.

it might be still possible to change this abi on linux by
default, but i don't know what's the right way to manage the
abi transition. i will have to think about it.

i dont think PROT_MTE|PROT_EXEC is architecturally well
supported (e.g. to have different colored functions or
similar, pc relative addressing doesn't work right).

(tbi for instruction pointers is unlikely to be useful, but
extra 8 bits for pac is useful. i think we should be able to
move to an abi that is compatible with either setting.)

(i think supporting mmap/munmap/madvise/mprotect on malloced
memory is problematic in general not just with heap tagging
so it would be nice to fix whatever jit that marks malloced
memory as executable.)

Hi Szabolcs,

Did you get a chance to think about this?

I propose that we start with a command line option that defaults to
off. If/when any ABI transition happens we can change the default.

Peter

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel