Re: Aw: Re: [PATCH] Fix mt7622.dtsi thermal cpu
From: Daniel Lezcano <hidden>
Date: 2021-06-25 09:57:10
Also in:
linux-devicetree, linux-mediatek, lkml
Hi Frank, On 25/06/2021 10:16, Frank Wunderlich wrote:
Hi,
quoted
Gesendet: Donnerstag, 24. Juni 2021 um 15:29 Uhr Von: "Eric Woudstra" [off-list ref] The SOC runs unthrotlled slowly to 80 degrees. This takes minutes.
Polling interval 1 second or less does not matter much when looking at these temperature rise times
quoted
After that in more then an hour it slowly creeps up to 85. I believe
the design is so that the SOC, under normal circumstances, can run at 1.35 GHz without throttling frequency, without heatsink. It just needs a safeguard for different circumstances.
quoted
Most of these SOCs can also run in industrial grade circumstances,
which means up to 85 degrees ambient temperature already . If not industrial then this would be 60 degrees ambient already
quoted
But only someone at Mediatek can confirm thismaybe Matthias knows anybody? get_maintainers-script shows no mtk employee for mtk_thermal driver,
added Sean and Ryder as common Linux-Contacts...
Daniel from openwrt have some other mt7622 Boards maybe he can test
the Fan approach below
quoted
On Jun 24, 2021, 12:21 PM, at 12:21 PM, Daniel Lezcano
[off-list ref] wrote:
quoted
quoted
Found that:
https://download.kamami.pl/p579344-MT7622A_Datasheet_for_BananaPi_Only%281%29.pdf
quoted
quoted
Chapter 3.3 - Thermal Characteristics Given the values I suggest: - Passive - 80°C - Hot - 90°C - Critical - 100°Cmaybe adding FAN (r64, don't know for other mt7622 boards) for lower 2
trips (with adjusted temperature points) and cpu-throtteling for upper 2 trips It depends what you want to achieve first: - better / sustained performance, then fan before - quiet device or power saving (on battery) then cpu throttling before That is board specific, it should be tuned on DT board specific file. Some comments below:
quoted hunk ↗ jump to hunk
something like this (used the 70/80 trip points discussed before):--- a/arch/arm64/boot/dts/mediatek/mt7622.dtsi +++ b/arch/arm64/boot/dts/mediatek/mt7622.dtsi
You should not add the fan in the mt7622.dtsi itself but in the board specific file where there is a fan output on it. mt7622.dtsi is supposed to be the SoC itself AFAICT. For instance: https://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux.git/tree/arch/arm64/boot/dts/rockchip/rk3399-sapphire.dtsi#n39 https://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux.git/tree/arch/arm64/boot/dts/rockchip/rk3399-sapphire.dtsi#n164
quoted hunk ↗ jump to hunk
@@ -134,6 +134,13 @@ }; }; + fan0: pwm-fan { + compatible = "pwm-fan"; + #cooling-cells = <2>; + pwms = <&pwm 2 10000 0>; + cooling-levels = <0 102 170 230>; + }; + thermal-zones { cpu_thermal: cpu-thermal { polling-delay-passive = <1000>;@@ -143,13 +150,13 @@ trips { cpu_passive: cpu-passive { - temperature = <47000>; + temperature = <70000>; hysteresis = <2000>; type = "passive"; }; cpu_active: cpu-active { - temperature = <67000>; + temperature = <80000>; hysteresis = <2000>; type = "active"; };@@ -170,14 +177,12 @@ cooling-maps { map0 { trip = <&cpu_passive>; - cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, - <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + cooling-device = <&fan0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; };
fan == active trip point This is referring to the passive trip point. So it should point to the CPU as it is now. Note the order of mitigation is inverted regarding the proposal description.
quoted hunk ↗ jump to hunk
map1 { trip = <&cpu_active>; - cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, - <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + cooling-device = <&fan0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; }; map2 {@@ -428,6 +433,7 @@ pwm: pwm@11006000 { compatible = "mediatek,mt7622-pwm"; reg = <0 0x11006000 0 0x1000>; + #pwm-cells = <3>; interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_LOW>; clocks = <&topckgen CLK_TOP_PWM_SEL>, <&pericfg CLK_PERI_PWM_PD>,regards Frank
-- <http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook | <http://twitter.com/#!/linaroorg> Twitter | <http://www.linaro.org/linaro-blog/> Blog _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel