Re: [PATCH 2/2] dt-bindings: opp: Convert to DT schema
From: Viresh Kumar <viresh.kumar@linaro.org>
Date: 2021-06-24 04:32:56
Also in:
dri-devel, linux-devicetree, linux-pm, lkml
Thanks for taking it up :) On 23-06-21, 17:07, Rob Herring wrote:
quoted hunk ↗ jump to hunk
diff --git a/Documentation/devicetree/bindings/opp/opp-v2-base.yaml b/Documentation/devicetree/bindings/opp/opp-v2-base.yaml +$id: http://devicetree.org/schemas/opp/opp-v2-base.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Generic OPP (Operating Performance Points) Common Binding + +maintainers: + - Viresh Kumar <viresh.kumar@linaro.org> + +description: | + Devices work at voltage-current-frequency combinations and some implementations + have the liberty of choosing these. These combinations are called Operating + Performance Points aka OPPs. This document defines bindings for these OPPs + applicable across wide range of devices. For illustration purpose, this document + uses CPU as a device. + + This describes the OPPs belonging to a device. + +select: false + +properties: + $nodename: + pattern: '^opp-table(-[a-z0-9]+)?$' + + opp-shared: + description: + Indicates that device nodes using this OPP Table Node's phandle switch + their DVFS state together, i.e. they share clock/voltage/current lines. + Missing property means devices have independent clock/voltage/current + lines, but they share OPP tables. + type: boolean + +patternProperties: + '^opp-?[0-9]+$': + type: object + description: + One or more OPP nodes describing voltage-current-frequency combinations. + Their name isn't significant but their phandle can be used to reference an + OPP. These are mandatory except for the case where the OPP table is + present only to indicate dependency between devices using the opp-shared + property. + + properties: + opp-hz: + description: + Frequency in Hz, expressed as a 64-bit big-endian integer. This is a + required property for all device nodes, unless another "required" + property to uniquely identify the OPP nodes exists. Devices like power + domains must have another (implementation dependent) property. + + opp-peak-kBps: + description: + Peak bandwidth in kilobytes per second, expressed as an array of + 32-bit big-endian integers. Each element of the array represents the + peak bandwidth value of each interconnect path. The number of elements + should match the number of interconnect paths. + minItems: 1 + maxItems: 32 # Should be enough
Can we move this down, closer to opp-avg-kBps ?
+ + opp-microvolt: + description: | + Voltage for the OPP + + A single regulator's voltage is specified with an array of size one or three. + Single entry is for target voltage and three entries are for <target min max> + voltages. + + Entries for multiple regulators shall be provided in the same field separated + by angular brackets <>. The OPP binding doesn't provide any provisions to + relate the values to their power supplies or the order in which the supplies + need to be configured and that is left for the implementation specific + binding. + + Entries for all regulators shall be of the same size, i.e. either all use a + single value or triplets. + minItems: 1 + maxItems: 8
For consistency with rest of the doc, maybe add # Should be enough regulators
+ items: + minItems: 1 + maxItems: 3 + + opp-microamp: + description: | + The maximum current drawn by the device in microamperes considering + system specific parameters (such as transients, process, aging, + maximum operating temperature range etc.) as necessary. This may be + used to set the most efficient regulator operating mode. + + Should only be set if opp-microvolt(-name)? is set for the OPP.
What is the significance of '?' here ?
+ + Entries for multiple regulators shall be provided in the same field + separated by angular brackets <>. If current values aren't required + for a regulator, then it shall be filled with 0. If current values + aren't required for any of the regulators, then this field is not + required. The OPP binding doesn't provide any provisions to relate the + values to their power supplies or the order in which the supplies need + to be configured and that is left for the implementation specific + binding. + minItems: 1 + maxItems: 8 # Should be enough regulators + items: + minItems: 1 + maxItems: 3
Acked-by: Viresh Kumar <viresh.kumar@linaro.org> -- viresh _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel