Re: [PATCH v2 1/2] serial: 8250: Add UART_BUG_TXRACE workaround for Aspeed VUART
From: Joel Stanley <joel@jms.id.au>
Date: 2021-05-19 00:59:15
Also in:
linux-aspeed, linux-serial, lkml, openbmc
On Wed, 19 May 2021 at 00:07, Andrew Jeffery [off-list ref] wrote:
Aspeed Virtual UARTs directly bridge e.g. the system console UART on the LPC bus to the UART interface on the BMC's internal APB. As such there's no RS-232 signalling involved - the UART interfaces on each bus are directly connected as the producers and consumers of the one set of FIFOs. The APB in the AST2600 generally runs at 100MHz while the LPC bus peaks at 33MHz. The difference in clock speeds exposes a race in the VUART design where a Tx data burst on the APB interface can result in a byte lost on the LPC interface. The symptom is LSR[DR] remains clear on the LPC interface despite data being present in its Rx FIFO, while LSR[THRE] remains clear on the APB interface as the host has not consumed the data the BMC has transmitted. In this state, the UART has stalled and no further data can be transmitted without manual intervention (e.g. resetting the FIFOs, resulting in loss of data). The recommended work-around is to insert a read cycle on the APB interface between writes to THR. Cc: ChiaWei Wang <redacted> Signed-off-by: Andrew Jeffery <redacted>
Reviewed-by: Joel Stanley <joel@jms.id.au>
quoted hunk ↗ jump to hunk
--- drivers/tty/serial/8250/8250.h | 1 + drivers/tty/serial/8250/8250_aspeed_vuart.c | 1 + drivers/tty/serial/8250/8250_port.c | 10 ++++++++++ 3 files changed, 12 insertions(+)diff --git a/drivers/tty/serial/8250/8250.h b/drivers/tty/serial/8250/8250.h index 52bb21205bb6..34aa2714f3c9 100644 --- a/drivers/tty/serial/8250/8250.h +++ b/drivers/tty/serial/8250/8250.h@@ -88,6 +88,7 @@ struct serial8250_config { #define UART_BUG_NOMSR (1 << 2) /* UART has buggy MSR status bits (Au1x00) */ #define UART_BUG_THRE (1 << 3) /* UART has buggy THRE reassertion */ #define UART_BUG_PARITY (1 << 4) /* UART mishandles parity if FIFO enabled */ +#define UART_BUG_TXRACE (1 << 5) /* UART Tx fails to set remote DR */ #ifdef CONFIG_SERIAL_8250_SHARE_IRQdiff --git a/drivers/tty/serial/8250/8250_aspeed_vuart.c b/drivers/tty/serial/8250/8250_aspeed_vuart.c index a28a394ba32a..4caab8714e2c 100644 --- a/drivers/tty/serial/8250/8250_aspeed_vuart.c +++ b/drivers/tty/serial/8250/8250_aspeed_vuart.c@@ -440,6 +440,7 @@ static int aspeed_vuart_probe(struct platform_device *pdev) port.port.status = UPSTAT_SYNC_FIFO; port.port.dev = &pdev->dev; port.port.has_sysrq = IS_ENABLED(CONFIG_SERIAL_8250_CONSOLE); + port.bugs |= UART_BUG_TXRACE;
A future enhancement would be to have this depend on the ast2600 compatible string, so we don't enable the feature for ast2400/ast2500. That would also mean adding a compatible string for the ast2600. Cheers, Joel _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel