Thread (11 messages) flat view 11 messages, 5 authors, 2021-06-28

Re: [PATCH v3 2/3] net: ethernet: actions: Add Actions Semi Owl Ethernet MAC driver

From: Andrew Lunn <andrew@lunn.ch>
Date: 2021-03-22 23:39:44
Also in: linux-devicetree, lkml, netdev

+static void owl_emac_set_multicast(struct net_device *netdev, int count)
+{
+	struct owl_emac_priv *priv = netdev_priv(netdev);
+	struct netdev_hw_addr *ha;
+	int index = 0;
+
+	if (count <= 0) {
+		priv->mcaddr_list.count = 0;
+		return;
+	}
+
+	netdev_for_each_mc_addr(ha, netdev) {
+		if (!is_multicast_ether_addr(ha->addr))
+			continue;
Is this possible?
+
+		WARN_ON(index >= OWL_EMAC_MAX_MULTICAST_ADDRS);
+		ether_addr_copy(priv->mcaddr_list.addrs[index++], ha->addr);
+	}
+
+	priv->mcaddr_list.count = index;
+
+	owl_emac_setup_frame_xmit(priv);
+}
+
+static void owl_emac_ndo_set_rx_mode(struct net_device *netdev)
+{
+	struct owl_emac_priv *priv = netdev_priv(netdev);
+	u32 status, val = 0;
+	int mcast_count = 0;
+
+	if (netdev->flags & IFF_PROMISC) {
+		val = OWL_EMAC_BIT_MAC_CSR6_PR;
+	} else if (netdev->flags & IFF_ALLMULTI) {
+		val = OWL_EMAC_BIT_MAC_CSR6_PM;
+	} else if (netdev->flags & IFF_MULTICAST) {
+		mcast_count = netdev_mc_count(netdev);
+
+		if (mcast_count > OWL_EMAC_MAX_MULTICAST_ADDRS) {
+			val = OWL_EMAC_BIT_MAC_CSR6_PM;
+			mcast_count = 0;
+		}
+	}
+
+	spin_lock_bh(&priv->lock);
+
+	/* Temporarily stop DMA TX & RX. */
+	status = owl_emac_dma_cmd_stop(priv);
+
+	/* Update operation modes. */
+	owl_emac_reg_update(priv, OWL_EMAC_REG_MAC_CSR6,
+			    OWL_EMAC_BIT_MAC_CSR6_PR | OWL_EMAC_BIT_MAC_CSR6_PM,
+			    val);
+
+	/* Restore DMA TX & RX status. */
+	owl_emac_dma_cmd_set(priv, status);
+
+	spin_unlock_bh(&priv->lock);
+
+	/* Set/reset multicast addr list. */
+	owl_emac_set_multicast(netdev, mcast_count);
+}
I think this can be simplified. At least, you had me going around in
circles a while trying to see if WARN_ON() could be triggered from
user space.

If you have more than OWL_EMAC_MAX_MULTICAST_ADDRS MC addresses, you
go into promisc mode. Can you then skip calling
owl_emac_set_multicast(), which appears not to do too much useful when
passed 0?

       Andrew

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Keyboard shortcuts
hback out one level
jnext message in thread
kprevious message in thread
ldrill in
Escclose help / fold thread tree
?toggle this help