[PATCH net 1/1] net: stmmac: fix CBS idleslope and sendslope calculation
From: Song Yoong Siang <hidden>
Date: 2021-02-18 06:07:04
Also in:
lkml, netdev
Subsystem:
networking drivers, stmmac ethernet driver, the rest · Maintainers:
Andrew Lunn, "David S. Miller", Eric Dumazet, Jakub Kicinski, Paolo Abeni, Linus Torvalds
From: "Song, Yoong Siang" <redacted>
When link speed is not 100 Mbps, port transmit rate and speed divider
are set to 8 and 1000000 respectively. These values are incorrect for
CBS idleslope and sendslope HW values calculation if the link speed is
not 1 Gbps.
This patch adds switch statement to set the values of port transmit rate
and speed divider for 10 Gbps, 5 Gbps, 2.5 Gbps, 1 Gbps, and 100 Mbps.
Note that CBS is not supported at 10 Mbps.
Fixes: bc41a6689b30 ("net: stmmac: tc: Remove the speed dependency")
Fixes: 1f705bc61aee ("net: stmmac: Add support for CBS QDISC")
Signed-off-by: Song, Yoong Siang <redacted>
---
drivers/net/ethernet/stmicro/stmmac/stmmac_tc.c | 30 +++++++++++++++++++++----
1 file changed, 26 insertions(+), 4 deletions(-)
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_tc.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_tc.c
index 5698554..44bb133 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_tc.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_tc.c@@ -316,6 +316,32 @@ static int tc_setup_cbs(struct stmmac_priv *priv, if (!priv->dma_cap.av) return -EOPNOTSUPP; + /* Port Transmit Rate and Speed Divider */ + switch (priv->speed) { + case SPEED_10000: + ptr = 32; + speed_div = 10000000; + break; + case SPEED_5000: + ptr = 32; + speed_div = 5000000; + break; + case SPEED_2500: + ptr = 8; + speed_div = 2500000; + break; + case SPEED_1000: + ptr = 8; + speed_div = 1000000; + break; + case SPEED_100: + ptr = 4; + speed_div = 100000; + break; + default: + return -EOPNOTSUPP; + } + mode_to_use = priv->plat->tx_queues_cfg[queue].mode_to_use; if (mode_to_use == MTL_QUEUE_DCB && qopt->enable) { ret = stmmac_dma_qmode(priv, priv->ioaddr, queue, MTL_QUEUE_AVB);
@@ -332,10 +358,6 @@ static int tc_setup_cbs(struct stmmac_priv *priv, priv->plat->tx_queues_cfg[queue].mode_to_use = MTL_QUEUE_DCB; } - /* Port Transmit Rate and Speed Divider */ - ptr = (priv->speed == SPEED_100) ? 4 : 8; - speed_div = (priv->speed == SPEED_100) ? 100000 : 1000000; - /* Final adjustments for HW */ value = div_s64(qopt->idleslope * 1024ll * ptr, speed_div); priv->plat->tx_queues_cfg[queue].idle_slope = value & GENMASK(31, 0);
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel