On Tue, Feb 09, 2021 at 11:11:54AM +0100, Michal Simek wrote:

On 2/9/21 11:03 AM, Greg Kroah-Hartman wrote:

quoted

On Tue, Feb 09, 2021 at 10:53:20AM +0100, Michal Simek wrote:

quoted

From: Piyush Mehta <redacted>

This patch adds a USB GPIO based hub reset for USB5744 hub. This usb5744
driver trigger hub reset signal after soft reset or core Reset. The HUB
needs to be resetted after completion of phy initialization. After the
toggling of gpio, hub configure using i2c usb attached command.

USB5744 hub can be used without any I2C connection, is handled by a
simple platform device driver.

As part of the reset, sets the direction of the pin to output before
toggling the pin. Delay of millisecond is added in between low and
high to meet the setup and hold time requirement of the reset.

Signed-off-by: Piyush Mehta <redacted>
Signed-off-by: Michal Simek <redacted>
---

 MAINTAINERS                |   1 +
 drivers/usb/misc/Kconfig   |   9 +++
 drivers/usb/misc/Makefile  |   1 +
 drivers/usb/misc/usb5744.c | 115 +++++++++++++++++++++++++++++++++++++
 4 files changed, 126 insertions(+)
 create mode 100644 drivers/usb/misc/usb5744.c

diff --git a/MAINTAINERS b/MAINTAINERS
index 7439471b5d37..56d1fcdd24f6 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS

@@ -2706,6 +2706,7 @@ F:	drivers/edac/synopsys_edac.c
 F:	drivers/i2c/busses/i2c-cadence.c
 F:	drivers/i2c/busses/i2c-xiic.c
 F:	drivers/mmc/host/sdhci-of-arasan.c
+F:	drivers/usb/misc/usb5744.c
 N:	zynq
 N:	xilinx
 

diff --git a/drivers/usb/misc/Kconfig b/drivers/usb/misc/Kconfig
index 8f1144359012..30335b5c4f88 100644
--- a/drivers/usb/misc/Kconfig
+++ b/drivers/usb/misc/Kconfig

@@ -242,6 +242,15 @@ config USB_HUB_USB251XB
 	  parameters may be set in devicetree or platform data.
 	  Say Y or M here if you need to configure such a device via SMBus.
 
+config USB_USB5744
+	tristate "Microchip USB5744 Hub driver"
+	depends on I2C
+	depends on GPIOLIB
+	help
+	  This option enables support for Microchip USB5744 Hub. This driver
+	  optionally reset the hub using gpio pin and configure hub via i2c if
+	  connected.
+
 config USB_HSIC_USB3503
 	tristate "USB3503 HSIC to USB20 Driver"
 	depends on I2C

diff --git a/drivers/usb/misc/Makefile b/drivers/usb/misc/Makefile
index 5f4e598573ab..5920146a506a 100644
--- a/drivers/usb/misc/Makefile
+++ b/drivers/usb/misc/Makefile

@@ -25,6 +25,7 @@ obj-$(CONFIG_USB_USS720)		+= uss720.o
 obj-$(CONFIG_USB_SEVSEG)		+= usbsevseg.o
 obj-$(CONFIG_USB_YUREX)			+= yurex.o
 obj-$(CONFIG_USB_HUB_USB251XB)		+= usb251xb.o
+obj-$(CONFIG_USB_USB5744)		+= usb5744.o

Can you follow the convention of the config options we have already, and
make this USB_HUB_USB5744 please?

Sure.

quoted

quoted

 obj-$(CONFIG_USB_HSIC_USB3503)		+= usb3503.o
 obj-$(CONFIG_USB_HSIC_USB4604)		+= usb4604.o

And then put it in sorted order :)

Do you want me to sort the whole Makefile and Kconfig as separate patch?

No, but at least put your new line in the obvious place, in order :)

And any other problem with the driver itself?

No idea, I stopped here in reviewing...

thanks,

greg k-h

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel