Re: [PATCH v3 4/4] arm64: dts: freescale: Add support for phyBOARD-Pollux-i.MX8MP
From: Teresa Remmet <hidden>
Date: 2021-01-07 06:58:09
Also in:
linux-devicetree
Hello Shawn, Am Donnerstag, den 07.01.2021, 14:22 +0800 schrieb Shawn Guo:
On Fri, Dec 11, 2020 at 02:48:55PM +0100, Teresa Remmet wrote:quoted
Add initial support for phyBOARD-Pollux-i.MX8MP. Supported basic features: * eMMC * i2c EEPROM * i2c RTC * i2c LED * PMIC * debug UART * SD card * 1Gbit Ethernet (fec) * watchdog Signed-off-by: Teresa Remmet <redacted> Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> --- arch/arm64/boot/dts/freescale/Makefile | 1 + .../dts/freescale/imx8mp-phyboard-pollux-rdk.dts | 163 ++++++++++++ .../boot/dts/freescale/imx8mp-phycore-som.dtsi | 296 +++++++++++++++++++++ 3 files changed, 460 insertions(+) create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-phyboard- pollux-rdk.dts create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-phycore- som.dtsi
[...]
quoted
+} + +/* ethernet 1 */ +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec>; + phy-mode = "rgmii-id"; + phy-handle = <ðphy1>; + fsl,magic-packet; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy1: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + interrupt-parent = <&gpio1>; + interrupts = <15 IRQ_TYPE_EDGE_FALLING>; + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>; + ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>; + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; + ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>; + enet-phy-lane-no-swap;Undocumented property?
yes it is undocumented but used by the drivers/net/phy/dp83867.c eth phy driver.
quoted
+ }; + }; +}; + +&i2c1 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + pinctrl-1 = <&pinctrl_i2c1_gpio>; + sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + status = "okay"; + + pmic: pmic@25 { + reg = <0x25>; + compatible = "nxp,pca9450c"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pmic>; + interrupt-parent = <&gpio4>; + interrupts = <18 IRQ_TYPE_LEVEL_LOW>; + + regulators { + buck1: BUCK1 { + regulator-compatible = "BUCK1"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <2187500>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <3125>; + }; + + buck2: BUCK2 { + regulator-compatible = "BUCK2"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <2187500>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <3125>; + }; + + buck4: BUCK4 { + regulator-compatible = "BUCK4"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <3400000>; + regulator-boot-on; + regulator-always-on; + }; + + buck5: BUCK5 { + regulator-compatible = "BUCK5"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <3400000>; + regulator-boot-on; + regulator-always-on; + }; + + buck6: BUCK6 { + regulator-compatible = "BUCK6"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <3400000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1: LDO1 { + regulator-compatible = "LDO1"; + regulator-min-microvolt = <1600000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo2: LDO2 { + regulator-compatible = "LDO2"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1150000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo3: LDO3 { + regulator-compatible = "LDO3"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo4: LDO4 { + regulator-compatible = "LDO4"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo5: LDO5 { + regulator-compatible = "LDO5"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + }; + }; + + eeprom@51 { + compatible = "atmel,24c32"; + reg = <0x51>; + pagesize = <32>; + status = "okay";Unneeded 'okay' status.quoted
+ }; + + rv3028: rtc@52 { + compatible = "microcrystal,rv3028"; + reg = <0x52>; + trickle-resistor-ohms = <1000>; + enable-level-switching-mode;Undocumented property?
This is a downstream leftover. I will remove it. Same with the unneeded status properties. Thank you for the review. Teresa
Shawn
_______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel