[PATCH 3/3] ARM: dts: add Ebang EBAZ4205 device tree
From: Michael Walle <hidden>
Date: 2021-01-20 19:47:37
Also in:
linux-devicetree, lkml
Subsystem:
arm and arm64 soc sub-architectures (common parts), the rest · Maintainers:
Arnd Bergmann, Krzysztof Kozlowski, Alexandre Belloni, Linus Walleij, Linus Torvalds
The Ebang EBAZ4205 is a simple board based on the Xilinx Zynq-7000 SoC. Its features are: - one serial port - 256 MB RAM - 128 MB NAND flash - SDcard slot - IP101GA 10/100 Mbit Ethernet PHY (connected to PL IOs) - two LEDs (connected to PL IOs) - one Push Button (connect to PL IOs) - (optional) RTC - (optional) Input voltage supervisor The NAND flash is not supported in mainline linux yet. Unfortunately, the PHY is connected via the PL, thus for working ethernet the FPGA has to be configured. Also, depending on the board variant, the PHY has no external crystal and its clock needs to be driven by the PL. FCLK3 is used for this and is kept enabled. Signed-off-by: Michael Walle <redacted> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/zynq-ebaz4205.dts | 109 ++++++++++++++++++++++++++++ 2 files changed, 110 insertions(+) create mode 100644 arch/arm/boot/dts/zynq-ebaz4205.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index bf80fd901f61..03ac2e665241 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile@@ -1312,6 +1312,7 @@ dtb-$(CONFIG_ARCH_VT8500) += \ wm8850-w70v2.dtb dtb-$(CONFIG_ARCH_ZYNQ) += \ zynq-cc108.dtb \ + zynq-ebaz4205.dtb \ zynq-microzed.dtb \ zynq-parallella.dtb \ zynq-zc702.dtb \
diff --git a/arch/arm/boot/dts/zynq-ebaz4205.dts b/arch/arm/boot/dts/zynq-ebaz4205.dts
new file mode 100644
index 000000000000..e802d4ae8804
--- /dev/null
+++ b/arch/arm/boot/dts/zynq-ebaz4205.dts@@ -0,0 +1,109 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2021 Michael Walle <michael@walle.cc> + */ +/dts-v1/; +/include/ "zynq-7000.dtsi" + +/ { + model = "Ebang EBAZ4205"; + compatible = "ebang,ebaz4205", "xlnx,zynq-7000"; + + aliases { + ethernet0 = &gem0; + serial0 = &uart1; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x10000000>; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&clkc { + ps-clk-frequency = <33333333>; + fclk-enable = <8>; +}; + +&gem0 { + status = "okay"; + phy-mode = "mii"; + phy-handle = <&phy>; + + /* PHY clock */ + assigned-clocks = <&clkc 18>; + assigned-clock-rates = <25000000>; + + phy: ethernet-phy@0 { + reg = <0>; + }; +}; + +&pinctrl0 { + pinctrl_sdhci0_default: sdhci0-default { + mux { + groups = "sdio0_2_grp"; + function = "sdio0"; + }; + + conf { + groups = "sdio0_2_grp"; + io-standard = <3>; + slew-rate = <0>; + bias-disable; + }; + + mux-cd { + groups = "gpio0_34_grp"; + function = "sdio0_cd"; + }; + + conf-cd { + groups = "gpio0_34_grp"; + io-standard = <3>; + slew-rate = <0>; + bias-high-impedance; + bias-pull-up; + }; + }; + + pinctrl_uart1_default: uart1-default { + mux { + groups = "uart1_4_grp"; + function = "uart1"; + }; + + conf { + groups = "uart1_4_grp"; + io-standard = <3>; + slew-rate = <0>; + }; + + conf-rx { + pins = "MIO25"; + bias-high-impedance; + }; + + conf-tx { + pins = "MIO24"; + bias-disable; + }; + }; +}; + +&sdhci0 { + status = "okay"; + disable-wp; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sdhci0_default>; +}; + +&uart1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1_default>; +};
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel