Re: [PATCH V2] arm64/hotplug: Improve memory offline event notifier

On 09/11/2020 07:36 PM, Catalin Marinas wrote:

Hi Anshuman,

On Mon, Aug 24, 2020 at 09:34:29AM +0530, Anshuman Khandual wrote:

quoted

This brings about three different changes to the sole memory event notifier
for arm64 platform and improves it's robustness while also enhancing debug
capabilities during potential memory offlining error conditions.

This moves the memory notifier registration bit earlier in the boot process
from device_initcall() to setup_arch() which will help in guarding against
potential early boot memory offline requests.

This enables MEM_OFFLINE memory event handling. It will help intercept any
possible error condition such as if boot memory some how still got offlined
even after an expilicit notifier failure, potentially by a future change in
generic hotplug framework. This would help detect such scenarious and help
debug further.

It also adds a validation function which scans entire boot memory and makes
sure that early memory sections are online. This check is essential for the
memory notifier to work properly as it cannot prevent boot memory offlining
if they are not online to begin with. But this additional sanity check is
enabled only with DEBUG_VM.

Could you please split this in separate patches rather than having a
single one doing three somewhat related things?

Sure, will do.

quoted

--- a/arch/arm64/kernel/setup.c
+++ b/arch/arm64/kernel/setup.c

@@ -376,6 +376,14 @@ void __init __no_sanitize_address setup_arch(char **cmdline_p)
 			"This indicates a broken bootloader or old kernel\n",
 			boot_args[1], boot_args[2], boot_args[3]);
 	}
+
+	/*
+	 * Register the memory notifier which will prevent boot
+	 * memory offlining requests - early enough. But there
+	 * should not be any actual offlinig request till memory
+	 * block devices are initialized with memory_dev_init().
+	 */
+	memory_hotremove_notifier();

Why can this not be an early_initcall()? As you said, memory_dev_init()
is called much later, after the SMP was initialised.

This proposal moves memory_hotremove_notifier() to setup_arch() because it
could and there is no harm in calling this too early than required for now.
But in case generic MM sequence of events during memory init changes later,
this notifier will still work.

IIUC, the notifier chain registration can be called very early in the boot
process without much problem. There are some precedence on other platforms.

1. arch/s390/mm/init.c   		  - In device_initcall() via s390_cma_mem_init()
2. arch/s390/mm/setup.c  		  - In setup_arch() via reserve_crashkernel()
3. arch/powerpc/platforms/pseries/cmm.c   - In module_init() via cmm_init()
4. arch/powerpc/platforms/pseries/iommu.c - via iommu_init_early_pSeries()
					    via pSeries_init()
				            via pSeries_probe() aka ppc_md.porbe()
					    via probe_machine()
					    via setup_arch()

You could even combine this with validate_bootmem_online_state() in a
single early_initcall() which, after checking, registers the notifier.

Yes, that will be definitely simpler but there might be still some value
in having this registration in setup_arch() which guard against future
generic MM changes while keeping it separate from the sanity check i.e
validate_bootmem_online_state() which is enabled only with DEBUG_VM. But
will combine both in early_initcall() with some name changes if that is
preferred.

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel