[PATCH v8 01/19] spi: spi-mem: allow specifying whether an op is DTR or not
From: Pratyush Yadav <hidden>
Date: 2020-05-22 22:41:19
Also in:
linux-mediatek, linux-spi, lkml
Subsystem:
spi subsystem, the rest · Maintainers:
Mark Brown, Linus Torvalds
Each phase is given a separate 'dtr' field so mixed protocols like 4S-4D-4D can be supported. Signed-off-by: Pratyush Yadav <redacted> --- drivers/spi/spi-mem.c | 3 +++ include/linux/spi/spi-mem.h | 8 ++++++++ 2 files changed, 11 insertions(+)
diff --git a/drivers/spi/spi-mem.c b/drivers/spi/spi-mem.c
index 9a86cc27fcc0..93e255287ab9 100644
--- a/drivers/spi/spi-mem.c
+++ b/drivers/spi/spi-mem.c@@ -156,6 +156,9 @@ bool spi_mem_default_supports_op(struct spi_mem *mem, op->data.dir == SPI_MEM_DATA_OUT)) return false; + if (op->cmd.dtr || op->addr.dtr || op->dummy.dtr || op->data.dtr) + return false; + return true; } EXPORT_SYMBOL_GPL(spi_mem_default_supports_op);
diff --git a/include/linux/spi/spi-mem.h b/include/linux/spi/spi-mem.h
index af9ff2f0f1b2..e3dcb956bf61 100644
--- a/include/linux/spi/spi-mem.h
+++ b/include/linux/spi/spi-mem.h@@ -71,9 +71,11 @@ enum spi_mem_data_dir { * struct spi_mem_op - describes a SPI memory operation * @cmd.buswidth: number of IO lines used to transmit the command * @cmd.opcode: operation opcode + * @cmd.dtr: whether the command opcode should be sent in DTR mode or not * @addr.nbytes: number of address bytes to send. Can be zero if the operation * does not need to send an address * @addr.buswidth: number of IO lines used to transmit the address cycles + * @addr.dtr: whether the address should be sent in DTR mode or not * @addr.val: address value. This value is always sent MSB first on the bus. * Note that only @addr.nbytes are taken into account in this * address value, so users should make sure the value fits in the
@@ -81,7 +83,9 @@ enum spi_mem_data_dir { * @dummy.nbytes: number of dummy bytes to send after an opcode or address. Can * be zero if the operation does not require dummy bytes * @dummy.buswidth: number of IO lanes used to transmit the dummy bytes + * @dummy.dtr: whether the dummy bytes should be sent in DTR mode or not * @data.buswidth: number of IO lanes used to send/receive the data + * @data.dtr: whether the data should be sent in DTR mode or not * @data.dir: direction of the transfer * @data.nbytes: number of data bytes to send/receive. Can be zero if the * operation does not involve transferring data
@@ -91,22 +95,26 @@ enum spi_mem_data_dir { struct spi_mem_op { struct { u8 buswidth; + u8 dtr : 1; u8 opcode; } cmd; struct { u8 nbytes; u8 buswidth; + u8 dtr : 1; u64 val; } addr; struct { u8 nbytes; u8 buswidth; + u8 dtr : 1; } dummy; struct { u8 buswidth; + u8 dtr : 1; enum spi_mem_data_dir dir; unsigned int nbytes; union {
--
2.26.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel