Hi Rob,
On 2/6/20 7:21 PM, Rob Herring wrote:
On Thu, Jan 30, 2020 at 02:50:40PM +0100, Olivier Moysan wrote:
quoted
Convert the STM32 SAI bindings to DT schema format using json-schema.
Signed-off-by: Olivier Moysan <redacted>
---
.../bindings/sound/st,stm32-sai.txt | 107 ----------
.../bindings/sound/st,stm32-sai.yaml | 193 ++++++++++++++++++
2 files changed, 193 insertions(+), 107 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/sound/st,stm32-sai.txt
create mode 100644 Documentation/devicetree/bindings/sound/st,stm32-sai.yaml
quoted
diff --git a/Documentation/devicetree/bindings/sound/st,stm32-sai.yaml b/Documentation/devicetree/bindings/sound/st,stm32-sai.yaml
new file mode 100644
index 000000000000..33dca007fc86
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/st,stm32-sai.yaml
@@ -0,0 +1,193 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/sound/st,stm32-sai.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: STMicroelectronics STM32 Serial Audio Interface (SAI)
+
+maintainers:
+ - Olivier Moysan <olivier.moysan@st.com>
+
+description:
+ The SAI interface (Serial Audio Interface) offers a wide set of audio
+ protocols as I2S standards, LSB or MSB-justified, PCM/DSP, TDM, and AC'97.
+ The SAI contains two independent audio sub-blocks. Each sub-block has
+ its own clock generator and I/O lines controller.
+
+properties:
+ compatible:
+ enum:
+ - st,stm32f4-sai
+ - st,stm32h7-sai
+
+ reg:
+ items:
+ - description: Base address and size of SAI common register set.
+ - description: Base address and size of SAI identification register set.
+ minItems: 1
+ maxItems: 2
+
+ ranges:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ resets:
+ maxItems: 1
+
+ "#address-cells":
+ const: 1
+
+ "#size-cells":
+ const: 1
+
+ clocks:
+ items:
+ - description: pclk feeds the peripheral bus interface.
+ - description: x8k, SAI parent clock for sampling rates multiple of 8kHz.
+ - description: x11k, SAI parent clock for sampling rates multiple of 11.025kHz.
+
+ clock-names:
+ items:
+ enum: [ pclk, x8k, x11k ]
+ minItems: 3
+ maxItems: 3
+
+required:
+ - compatible
+ - reg
+ - ranges
+ - "#address-cells"
+ - "#size-cells"
+ - clocks
+ - clock-names
+
+patternProperties:
+ "^audio-controller@[0-9a-f]+$":
+ type: object
+ description:
+ Two subnodes corresponding to SAI sub-block instances A et B
+ can be defined. Subnode can be omitted for unsused sub-block.
+
+ properties:
+ compatible:
+ description: Compatible for SAI sub-block A or B.
+ enum:
+ - st,stm32-sai-sub-a
+ - st,stm32-sai-sub-b
pattern: 'st,stm32-sai-sub-[ab]'
I will change this in v2
quoted
+
+ "#sound-dai-cells":
+ const: 0
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ items:
+ - description: sai_ck clock feeding the internal clock generator.
+ - description: MCLK clock from a SAI set as master clock provider.
+ minItems: 1
+ maxItems: 2
+
+ clock-names:
+ items:
+ - const: sai_ck
+ - const: MCLK
+ minItems: 1
+ maxItems: 2
+
+ dmas:
+ items:
+ - description: SAI sub-block is configured as a capture DAI.
+ - description: SAI sub-block is configured as a playback DAI.
+ minItems: 1
+ maxItems: 1
This is defining that dmas has 2 entries, but then limits it to the 1st
entry only.
dma can be either "rx" or "tx", but not both.
Maybe, the following syntax is more appropriate:
dmas:
maxItems: 1
dma-names:
description: |
rx: SAI sub-block is configured as a capture DAI.
tx: SAI sub-block is configured as a playback DAI.
items:
- enum: [ rx, tx ]
quoted
+
+ dma-names:
+ items:
+ - enum: [ rx, tx ]
+
+ st,sync:
+ description:
+ Configure the SAI sub-block as slave of another SAI sub-block.
+ By default SAI sub-block is in asynchronous mode.
+ Must contain the phandle and index of the SAI sub-block providing
+ the synchronization.
+ allOf:
+ - $ref: /schemas/types.yaml#definitions/phandle-array
+ - maxItems: 1
+
+ st,iec60958:
+ description:
+ If set, support S/PDIF IEC6958 protocol for playback.
+ IEC60958 protocol is not available for capture.
+ By default, custom protocol is assumed, meaning that protocol is
+ configured according to protocol defined in related DAI link node,
+ such as i2s, left justified, right justified, dsp and pdm protocols.
+ allOf:
+ - $ref: /schemas/types.yaml#definitions/flag
+
+ "#clock-cells":
+ description: Configure the SAI device as master clock provider.
+ const: 0
+
+ required:
+ - compatible
+ - "#sound-dai-cells"
+ - reg
+ - clocks
+ - clock-names
+ - dmas
+ - dma-names
additionalProperties: false.
quoted
+
+allOf:
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: st,stm32f4-sai
+
+ - then:
+ properties:
+ clocks:
+ minItems: 2
+ maxItems: 2
+
+ clock-names:
+ items:
+ enum: [ x8k, x11k ]
Define the order.
Do you mean, adding in clocks property :
items:
- description: x8k, SAI parent clock for sampling rates
multiple of 8kHz.
- description: x11k, SAI parent clock for sampling rates
multiple of 11.025kHz.
But, it seems to me that this is redundant with previous definition of
clocks property.
Thanks
Olivier
quoted
+ minItems: 2
+ maxItems: 2
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/clock/stm32mp1-clks.h>
+ #include <dt-bindings/reset/stm32mp1-resets.h>
+ sai1: sai@4400a000 {
+ compatible = "st,stm32h7-sai";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x4400a000 0x400>;
+ reg = <0x4400a000 0x4>, <0x4400a3f0 0x10>;
+ interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&rcc SAI1>, <&rcc PLL1_Q>, <&rcc PLL2_P>;
+ clock-names = "pclk", "x8k", "x11k";
+ resets = <&rcc SAI1_R>;
+
+ sai1a: audio-controller@4400a004 {
+ compatible = "st,stm32-sai-sub-a";
+ #sound-dai-cells = <0>;
+ reg = <0x4 0x1c>;
+ clocks = <&rcc SAI1_K>;
+ clock-names = "sai_ck";
+ dmas = <&dmamux1 87 0x400 0x01>;
+ dma-names = "tx";
+ };
+ };
+
+...
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel