On 23.10.2019 19:34, Matthias Kaehlcke wrote:

On Wed, Oct 23, 2019 at 02:06:40PM +0000, Leonard Crestez wrote:

quoted

On 2019-10-02 10:25 PM, Leonard Crestez wrote:

quoted

Add dev_pm_qos notifiers to devfreq core in order to support frequency
limits via dev_pm_qos_add_request.

Unlike the rest of devfreq the dev_pm_qos frequency is measured in Khz,
this is consistent with current dev_pm_qos usage for cpufreq and
allows frequencies above 2Ghz (pm_qos expresses limits as s32).

Like with cpufreq the handling of min_freq/max_freq is moved to the
dev_pm_qos mechanism. Constraints from userspace are no longer clamped on
store, instead all values can be written and we only check against OPPs in a
new devfreq_get_freq_range function. This is consistent with the design of
dev_pm_qos.

Notifiers from pm_qos are executed under a single global dev_pm_qos_mtx and
need to take devfreq->lock. Notifier registration takes the same dev_pm_qos_mtx
so in order to prevent lockdep warnings it must be done outside devfreq->lock.
Current devfreq_add_device does all initialization under devfreq->lock and that
needs to be relaxed.

Some of first patches in the series are bugfixes and cleanups, they could be
applied separately.

Hello,

This series was posted a few ago and all patches have been
reviewed/tested-by multiple people. Possible minor hangups:

1) Matthias found it confusing that min/max_freq in sysfs changes
on-the-fly. This is not a behavior change and I believe a decent
workaround would be to implement separate user_min/max_freq files from
which userspace will always read back the contraints it has written.

As you said, it isn't a behavioral change, so it shouldn't be an issue
for this series.

Regarding the workaround I think it would be clearer to have new
xyx_min/max_freq files for the aggregate values. min/max_freq are the
interface userspace uses to specify the limits, it would be strange to
use different files to read them out.

In any case the aggregate values seem to be of little practical value,
except perhaps for monitoring, since they could be stale right after
userspace read them out. We could start with not providing them, and add
them if it turns out that they are actually needed.

But the min/max_freq files right now already are already aggregates and 
sysfs is considered ABI. I wouldn't be surprised if somebody has an 
userspace daemon which uses them.

My proposal is to add user_min/max_freq as a new finer-grained interface 
that you can both read and write to, no confusion here.

Writes to min/max_freq would still be supported but only for 
compatibility with older releases.

quoted

2) There was an objection to removing devm from two allocs in PATCH 4. I
believe current solution is acceptable but a possible alternative would
be to split device_register into device_initialize and device_add: this
should allow devm sooner.
Link: https://eur01.safelinks.protection.outlook.com/?url=https%3A%2F%2Fpatchwork.kernel.org%2Fpatch%2F11158385%2F%2322902151&data=02%7C01%7Cleonard.crestez%40nxp.com%7Cb89f3efc3c934030fb6108d757d6ecb2%7C686ea1d3bc2b4c6fa92cd99c5c301635%7C0%7C0%7C637074452911403311&sdata=DeOUpVjT1yZ2EWs50CFL98OoTjVMCpQDCM3qjCtKuW0%3D&reserved=0

Let me know if you think I should implement the options above and resend.

The bigger problem is that DEV_PM_QOS_MIN/MAX_FREQUENCY was removed from
pm core because only user (cpufreq) was refactored to use a new
interface on top of cpufreq_policy. Links to discussion:
      https://eur01.safelinks.protection.outlook.com/?url=https%3A%2F%2Fpatchwork.kernel.org%2Fcover%2F11193021%2F&data=02%7C01%7Cleonard.crestez%40nxp.com%7Cb89f3efc3c934030fb6108d757d6ecb2%7C686ea1d3bc2b4c6fa92cd99c5c301635%7C0%7C0%7C637074452911408301&sdata=DxfUtaGch6MilSy5fX8AHN3%2BDIp8MrbQrHH%2B6VdRb%2FI%3D&reserved=0
  
https://eur01.safelinks.protection.outlook.com/?url=https%3A%2F%2Flore.kernel.org%2Flinux-pm%2FVI1PR04MB7023DF47D046AEADB4E051EBEE680%40VI1PR04MB7023.eurprd04.prod.outlook.com%2FT%2F%23u&data=02%7C01%7Cleonard.crestez%40nxp.com%7Cb89f3efc3c934030fb6108d757d6ecb2%7C686ea1d3bc2b4c6fa92cd99c5c301635%7C0%7C0%7C637074452911408301&sdata=sYQZUbzEk2DsWGQ5eQnu2m2%2Bsp%2BYBO16Abyjwf7Z1sQ%3D&reserved=0

I believe there is still significant value in supporting min/max
frequency requests on a per-target-device basis. This makes much more
sense for devfreq that for cpufreq because the whole point of devfreq is
scaling arbitrary independent devices.

Agreed.

It seems Rafael would be ok with reverting the patch that removes
DEV_PM_QOS_MIN/MAX_FREQUENCY, IIUC he just doesn't want to keep it around
at this time because with the rest of his series there remain no in-tree
users.

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel