[PATCH] pinctrl: at91: Enable slewrate by default on SAM9X60
From: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Date: 2019-10-24 17:23:21
Also in:
linux-devicetree, linux-gpio, lkml
Subsystem:
open firmware and flattened device tree bindings, pin control subsystem, pin controller - microchip at91, the rest · Maintainers:
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Linus Walleij, Ludovic Desroches, Linus Torvalds
On SAM9X60, slewrate should be enabled on pins with a switching frequency below 50Mhz. Since most of our pins do not exceed this value, we enable slewrate by default. Pins with a switching value that exceeds 50Mhz will have to explicitly disable slewrate. Suggested-by: Ludovic Desroches <ludovic.desroches@microchip.com> Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com> --- drivers/pinctrl/pinctrl-at91.c | 4 ++-- include/dt-bindings/pinctrl/at91.h | 4 ++-- 2 files changed, 4 insertions(+), 4 deletions(-)
diff --git a/drivers/pinctrl/pinctrl-at91.c b/drivers/pinctrl/pinctrl-at91.c
index 117075b5798f..c135149e84e9 100644
--- a/drivers/pinctrl/pinctrl-at91.c
+++ b/drivers/pinctrl/pinctrl-at91.c@@ -85,8 +85,8 @@ enum drive_strength_bit { DRIVE_STRENGTH_SHIFT) enum slewrate_bit { - SLEWRATE_BIT_DIS, SLEWRATE_BIT_ENA, + SLEWRATE_BIT_DIS, }; #define SLEWRATE_BIT_MSK(name) (SLEWRATE_BIT_##name << SLEWRATE_SHIFT)
@@ -669,7 +669,7 @@ static void at91_mux_sam9x60_set_slewrate(void __iomem *pio, unsigned pin, { unsigned int tmp; - if (setting < SLEWRATE_BIT_DIS || setting > SLEWRATE_BIT_ENA) + if (setting < SLEWRATE_BIT_ENA || setting > SLEWRATE_BIT_DIS) return; tmp = readl_relaxed(pio + SAM9X60_PIO_SLEWR);
diff --git a/include/dt-bindings/pinctrl/at91.h b/include/dt-bindings/pinctrl/at91.h
index 3831f91fb3ba..e8e117306b1b 100644
--- a/include/dt-bindings/pinctrl/at91.h
+++ b/include/dt-bindings/pinctrl/at91.h@@ -27,8 +27,8 @@ #define AT91_PINCTRL_DRIVE_STRENGTH_MED (0x2 << 5) #define AT91_PINCTRL_DRIVE_STRENGTH_HI (0x3 << 5) -#define AT91_PINCTRL_SLEWRATE_DIS (0x0 << 9) -#define AT91_PINCTRL_SLEWRATE_ENA (0x1 << 9) +#define AT91_PINCTRL_SLEWRATE_ENA (0x0 << 9) +#define AT91_PINCTRL_SLEWRATE_DIS (0x1 << 9) #define AT91_PIOA 0 #define AT91_PIOB 1
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel