@@ -290,6 +290,23 @@ static void __init innovator_init_smc91x(void)
 }
 
 #ifdef CONFIG_ARCH_OMAP15XX
+/*
+ * Board specific gang-switched transceiver power on/off.
+ */
+static int innovator_omap_ohci_transceiver_power(int on)
+{
+	if (on)
+		__raw_writeb(__raw_readb(INNOVATOR_FPGA_CAM_USB_CONTROL)
+				| ((1 << 5/*usb1*/) | (1 << 3/*usb2*/)),
+			       INNOVATOR_FPGA_CAM_USB_CONTROL);
+	else
+		__raw_writeb(__raw_readb(INNOVATOR_FPGA_CAM_USB_CONTROL)
+				& ~((1 << 5/*usb1*/) | (1 << 3/*usb2*/)),
+			       INNOVATOR_FPGA_CAM_USB_CONTROL);
+
+	return 0;
+}
+
 static struct omap_usb_config innovator1510_usb_config __initdata = {
 	/* for bundled non-standard host and peripheral cables */
 	.hmc_mode	= 4,

@@ -300,6 +317,8 @@ static struct omap_usb_config innovator1510_usb_config __initdata = {
 
 	.register_dev	= 1,
 	.pins[0]	= 2,
+
+	.transceiver_power = innovator_omap_ohci_transceiver_power,
 };
 
 static const struct omap_lcd_config innovator1510_lcd_config __initconst = {

@@ -278,6 +278,23 @@ static void __init osk_init_cf(void)
 	irq_set_irq_type(gpio_to_irq(62), IRQ_TYPE_EDGE_FALLING);
 }
 
+/*
+ * Board specific gang-switched transceiver power on/off.
+ * NOTE:  OSK supplies power from DC, not battery.
+ */
+static int osk_omap_ohci_transceiver_power(int on)
+{
+	if (!IS_BUILTIN(CONFIG_TPS65010))
+		return -ENXIO;
+
+	if (on)
+		tps65010_set_gpio_out_value(GPIO1, LOW);
+	else
+		tps65010_set_gpio_out_value(GPIO1, HIGH);
+
+	return 0;
+}
+
 static struct omap_usb_config osk_usb_config __initdata = {
 	/* has usb host connector (A) ... for development it can also
 	 * be used, with a NONSTANDARD gender-bending cable/dongle, as

@@ -292,6 +309,8 @@ static struct omap_usb_config osk_usb_config __initdata = {
 	.rwc		= 1,
 #endif
 	.pins[0]	= 2,
+
+	.transceiver_power = osk_omap_ohci_transceiver_power,
 };
 
 #ifdef	CONFIG_OMAP_OSK_MISTRAL

@@ -77,31 +77,6 @@ static void omap_ohci_clock_power(int on)
 	}
 }
 
-/*
- * Board specific gang-switched transceiver power on/off.
- * NOTE:  OSK supplies power from DC, not battery.
- */
-static int omap_ohci_transceiver_power(int on)
-{
-	if (on) {
-		if (machine_is_omap_innovator() && cpu_is_omap1510())
-			__raw_writeb(__raw_readb(INNOVATOR_FPGA_CAM_USB_CONTROL)
-				| ((1 << 5/*usb1*/) | (1 << 3/*usb2*/)),
-			       INNOVATOR_FPGA_CAM_USB_CONTROL);
-		else if (machine_is_omap_osk())
-			tps65010_set_gpio_out_value(GPIO1, LOW);
-	} else {
-		if (machine_is_omap_innovator() && cpu_is_omap1510())
-			__raw_writeb(__raw_readb(INNOVATOR_FPGA_CAM_USB_CONTROL)
-				& ~((1 << 5/*usb1*/) | (1 << 3/*usb2*/)),
-			       INNOVATOR_FPGA_CAM_USB_CONTROL);
-		else if (machine_is_omap_osk())
-			tps65010_set_gpio_out_value(GPIO1, HIGH);
-	}
-
-	return 0;
-}
-
 #ifdef	CONFIG_USB_OTG
 
 static void start_hnp(struct ohci_hcd *ohci)

@@ -213,7 +188,8 @@ static int ohci_omap_reset(struct usb_hcd *hcd)
 	}
 
 	/* FIXME hub_wq hub requests should manage power switching */
-	omap_ohci_transceiver_power(1);
+	if (config->transceiver_power)
+		config->transceiver_power(1);
 
 	/* board init will have already handled HMC and mux setup.
 	 * any external transceiver should already be initialized

@@ -50,6 +50,8 @@ struct omap_usb_config {
 	int (*ocpi_enable)(void);
 
 	void (*lb_reset)(void);
+
+	int (*transceiver_power)(int on);
 };
 
 #endif /* __LINUX_USB_OMAP1_H */