Re: [PATCH 5/6] arm64: dts: Add ipq6018 SoC and CP01 board support

Hi Christian,

On 6/10/2019 5:45 PM, Christian Lamparter wrote:

On Monday, June 10, 2019 12:09:56 PM CEST Sricharan R wrote:

quoted

Hi Christian,

On 6/6/2019 2:11 AM, Christian Lamparter wrote:

quoted

On Wed, Jun 5, 2019 at 7:16 PM Sricharan R [off-list ref] wrote:

quoted

Add initial device tree support for the Qualcomm IPQ6018 SoC and
CP01 evaluation board.

Signed-off-by: Sricharan R <redacted>
Signed-off-by: Abhishek Sahu <redacted>

--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi

+       clocks {
+               sleep_clk: sleep_clk {
+                       compatible = "fixed-clock";
+                       clock-frequency = <32000>;
+                       #clock-cells = <0>;
+               };
+

Recently-ish, we ran into an issue with the clock-frequency of the sleep_clk
on older IPQ40XX (and IPQ806x) on the OpenWrt Github and ML.
From what I know, the external "32KHz" crystals have 32768 Hz, but the QSDK
declares them at 32000 Hz. Since you probably have access to the BOM and
datasheets. Can you please confirm what's the real clock frequency for
the IPQ6018.
(And maybe also for the sleep_clk of the IPQ4018 as well?).

What exactly is the issue that you faced ?
Looking in to the docs, it is <32000> only on ipq6018 and ipq40xx as well.

We need just a confirmation.

Then again, Currently the qcom-ipq4019.dtsi is using 32768 Hz.

|		sleep_clk: sleep_clk {
|			compatible = "fixed-clock";
|			clock-frequency = <32768>;
|			#clock-cells = <0>;
|		};

<https://github.com/torvalds/linux/blob/master/arch/arm/boot/dts/qcom-ipq4019.dtsi#L144>

Which makes sense, because all previous Qualcomm Atheros MIPS and the
future IPQ8072 SoCs have been either using or deriving a 32768 Hz clock.

For example: The AR9344 derives the clock from the 25MHz/40MHz external
oscillator. This is explained in "8.16.9 Derived RTC Clock (DERIVED_RTC_CLK)".
Which mentions that the "32KHz" clock interval is 30.5 usec / 30.48 usec
depending whenever the external reference crystal has 40MHz or 25MHz.
(1/30.5usec = 32.7868852 kilohertz!). The QCA9558 datasheet says the same
in "10.19.11 Derived RTC Clock". 

For IPQ8072: I point to the post by Sven Eckelmann on the OpenWrt ML:
<http://lists.infradead.org/pipermail/openwrt-devel/2019-May/017131.html>
"I was only able to verify for IPQ8072 that it had a 32.768 KHz
sleep clock." 

So this is pretty much "why there is an issue", it's confusing.
Is possible can you please look if there are (fixed) divisors values
listed in the documentation or the registers and bits that the values
are stored in? Because then we could just calculate it. 

Really sorry for the confusion. So looking little more, SLEEP_CLK is derived
from an external 38.4MHZ crystal, it is 32.768 KHZ. Somehow the
clk freq plan etc seems to mention them only as .032 MHZ and misses
out. That means i will correct the patch for 32768 and probably the
ipq8074.dtsi as well

Regards,
  Sricharan


-- 
"QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel