Hi Schrempf,

On 08.01.19 10:24, Yogesh Narayan Gaur wrote:

quoted

- Add driver for NXP FlexSPI host controller

  FlexSPI is a flexsible SPI host controller [1], Chapter 30 page
1475, which supports two SPI channels and up to 4 external devices.
  Each channel supports Single/Dual/Quad/Octal mode data transfer
(1/2/4/8 bidirectional data lines) i.e. FlexSPI acts as an
interface to external devices, maximum 4, each with up to 8
bidirectional data lines.

- Tested this driver with mtd_debug(Erase/Write/Read) utility and
JFFS2 filesystem mounting and booting on NXP LX2160ARDB[2] and
LX2160AQDS targets. LX2160ARDB is having two NOR slave device
connected on single bus A i.e. A0 and A1 (CS0 and CS1).
  LX2160AQDS is having two NOR slave device connected on separate
buses one flash on A0 and second on B1 i.e. (CS0 and CS3).
  Verified this driver on following SPI NOR flashes:
    Micron, mt35xu512aba, [Read - 1 bit mode]
    Cypress, s25fl512s, [Read - 1/2/4 bit mode]

[1] https://www.nxp.com/docs/en/reference-manual/IMXRT1050RM.pdf
[2]
https://patchwork.kernel.org/project/linux-arm-kernel/list/?submitter=182097

Yogesh Narayan Gaur (5):
   spi: spi-mem: Add driver for NXP FlexSPI controller
   dt-bindings: spi: add binding file for NXP FlexSPI controller
   arm64: dts: lx2160a: add FlexSPI node property
   arm64: defconfig: enable NXP FlexSPI driver
   MAINTAINERS: add maintainers for the NXP FlexSPI driver

Changes for v6:
- Rebase on top of v5.0-rc1.  

Your patches don't apply to v5.0-rc1. It seems like you have instead 
rebased onto the for-5.1 or for-next branch of the SPI tree. I guess 
this is okay, but you should have pointed that out correctly here.

If I may ask for a few (1-2) days, so I can test this code on vf610 NXP
SoC.

As fair as I remember there were some issues when I tested it a few
months back.

quoted

- Incorporated review comments for
   patch 'spi: spi-mem: Add driver for NXP FlexSPI controller'.
- Updated s-b tag in all patches.
Changes for v5:
- Rebase on top of v4.20-rc2
- Incorporated review comments for
   patch 'spi: spi-mem: Add driver for NXP FlexSPI controller'.
Changes for v4:
- Incorporated review comments for
   patch 'spi: spi-mem: Add driver for NXP FlexSPI controller'.
- Incorporated binding file review comments.
Changes for v3:
- Incorporated review comments for
   patch 'spi: spi-mem: Add driver for NXP FlexSPI controller'.
Changes for v2:
- Incorporated Boris review comments and drop below patches as per
the comments.
  - Patch 'spi: add slave device size in spi_device struct'
  - Patch 'spi: add flags for octal I/O data transfer'
- Incorporated DTS and Binding file review comments of Shawn Guo
and Rob Herring.

  .../devicetree/bindings/spi/spi-nxp-fspi.txt  |   39 +
  MAINTAINERS                                   |    7 +
  .../boot/dts/freescale/fsl-lx2160a-rdb.dts    |   22 +
  .../arm64/boot/dts/freescale/fsl-lx2160a.dtsi |   13 +
  arch/arm64/configs/defconfig                  |    1 +
  drivers/spi/Kconfig                           |   10 +
  drivers/spi/Makefile                          |    1 +
  drivers/spi/spi-nxp-fspi.c                    | 1095
+++++++++++++++++ 8 files changed, 1188 insertions(+)
  create mode 100644
Documentation/devicetree/bindings/spi/spi-nxp-fspi.txt create mode
100644 drivers/spi/spi-nxp-fspi.c 

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

Best regards,

Lukasz Majewski

--

DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lukma@denx.de