[PATCH v2 2/4] ARM: dts: s5pv210: aries: Support for more devices present on Aries
From: Paweł Chmiel <hidden>
Date: 2019-01-08 16:56:22
Also in:
linux-devicetree, linux-samsung-soc, lkml
Subsystem:
the rest · Maintainer:
Linus Torvalds
From: Jonathan Bakker <redacted>
This commit enables following devices present on Aries based phones:
- pwm-vibrator attached to PWM 1
- poweroff support
- Atmel maXTouch touchscreen, connected to i2c2
- Broadcom BCM4329 bluetooth over uart0
Signed-off-by: Jonathan Bakker <redacted>
Signed-off-by: Paweł Chmiel <redacted>
---
Changes from v1:
- Touchscreen irq pin should have PULL_NONE, since it's already
pulled up with 2.8v
- Touchscreen irq should be edge failing (like in vendor sources)
---
arch/arm/boot/dts/s5pv210-aries.dtsi | 68 ++++++++++++++++++++++++++++
1 file changed, 68 insertions(+)
diff --git a/arch/arm/boot/dts/s5pv210-aries.dtsi b/arch/arm/boot/dts/s5pv210-aries.dtsi
index 89525e56cc7c..8ff70b856334 100644
--- a/arch/arm/boot/dts/s5pv210-aries.dtsi
+++ b/arch/arm/boot/dts/s5pv210-aries.dtsi@@ -41,6 +41,13 @@ }; }; + vibrator_pwr: regulator-fixed-0 { + compatible = "regulator-fixed"; + regulator-name = "vibrator-en"; + enable-active-high; + gpio = <&gpj1 1 GPIO_ACTIVE_HIGH>; + }; + wifi_pwrseq: wifi-pwrseq { compatible = "mmc-pwrseq-simple"; reset-gpios = <&gpg1 2 GPIO_ACTIVE_LOW>;
@@ -314,6 +321,22 @@ reg = <0x36>; }; }; + + vibrator: pwm-vibrator { + compatible = "pwm-vibrator"; + pwms = <&pwm 1 44642 0>; + pwm-names = "enable"; + vcc-supply = <&vibrator_pwr>; + pinctrl-names = "default"; + pinctrl-0 = <&pwm1_out>; + }; + + poweroff: syscon-poweroff { + compatible = "syscon-poweroff"; + regmap = <&pmu_syscon>; + offset = <0x681c>; /* PS_HOLD_CONTROL */ + value = <0x5200>; + }; }; &fimd {
@@ -347,6 +370,23 @@ status = "okay"; }; +&i2c2 { + samsung,i2c-sda-delay = <100>; + samsung,i2c-max-bus-freq = <400000>; + samsung,i2c-slave-addr = <0x10>; + status = "okay"; + + touchscreen@4a { + compatible = "atmel,maxtouch"; + reg = <0x4a>; + interrupt-parent = <&gpj0>; + interrupts = <5 IRQ_TYPE_EDGE_FALLING>; + pinctrl-names = "default"; + pinctrl-0 = <&ts_irq>; + reset-gpios = <&gpj1 3 GPIO_ACTIVE_HIGH>; + }; +}; + &mfc { memory-region = <&mfc_left>, <&mfc_right>; };
@@ -372,6 +412,13 @@ samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; }; + bt_host_wake: bt-host-wake { + samsung,pins = "gph2-5"; + samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; + samsung,pin-pud = <S3C64XX_PIN_PULL_DOWN>; + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; + }; + tf_detect: tf-detect { samsung,pins = "gph3-4"; samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
@@ -384,6 +431,17 @@ samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>; }; + + ts_irq: ts-irq { + samsung,pins = "gpj0-5"; + samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; + samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>; + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; + }; +}; + +&pwm { + samsung,pwm-outputs = <1>; }; &sdhci1 {
@@ -421,6 +479,16 @@ &uart0 { status = "okay"; + + bluetooth { + compatible = "brcm,bcm43438-bt"; + max-speed = <115200>; + pinctrl-names = "default"; + pinctrl-0 = <&uart0_data &uart0_fctl &bt_host_wake>; + shutdown-gpios = <&gpb 3 GPIO_ACTIVE_HIGH>; + device-wakeup-gpios = <&gpg3 4 GPIO_ACTIVE_HIGH>; + host-wakeup-gpios = <&gph2 5 GPIO_ACTIVE_HIGH>; + }; }; &uart1 {
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel