@@ -0,0 +1,59 @@
+Qualcomm adreno/snapdragon GMU (Graphics management unit)
+
+The GMU is a programmable power controller for the GPU. the CPU controls the
+GMU which in turn handles power controls for the GPU.
+
+Required properties:
+- compatible: "qcom,adreno-gmu-XYZ.W", "qcom,adreno-gmu"
+    for example: "qcom,adreno-gmu-630.2", "qcom,adreno-gmu"
+  Note that you need to list the less specific "qcom,adreno-gmu"
+  for generic matches and the more specific identifier to identify
+  the specific device.
+- reg: Physical base address and length of the GMU registers.
+- reg-names: Matching names for the register regions
+  * "gmu"
+  * "gmu_pdc"
+  * "gmu_pdc_seg"
+- interrupts: The interrupt signals from the GMU.
+- interrupt-names: Matching names for the interrupts
+  * "hfi"
+  * "gmu"
+- clocks: phandles to the device clocks
+- clock-names: Matching names for the clocks
+   * "gmu"
+   * "cxo"
+   * "axi"
+   * "mnoc"
+- power-domains: should be <&clock_gpucc GPU_CX_GDSC>
+- iommus: phandle to the adreno iommu
+- operating-points-v2: phandle to the OPP operating points
+
+Example:
+
+/ {
+	...
+
+	gmu: gmu@506a000 {
+		compatible="qcom,adreno-gmu-630.2", "qcom,adreno-gmu";
+
+		reg = <0x506a000 0x30000>,
+			<0xb280000 0x10000>,
+			<0xb480000 0x10000>;
+		reg-names = "gmu", "gmu_pdc", "gmu_pdc_seq";
+
+		interrupts = <GIC_SPI 304 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "hfi", "gmu";
+
+		clocks = <&gpucc GPU_CC_CX_GMU_CLK>,
+			<&gpucc GPU_CC_CXO_CLK>,
+			<&gcc GCC_DDRSS_GPU_AXI_CLK>,
+			<&gcc GCC_GPU_MEMNOC_GFX_CLK>;
+		clock-names = "gmu", "cxo", "axi", "memnoc";
+
+		power-domains = <&gpucc GPU_CX_GDSC>;
+		iommus = <&adreno_smmu 5>;
+
+		operating-points-v2 = <&gmu_opp_table>;
+	};
+};

@@ -8,14 +8,23 @@ Required properties:
   with the chip-id.
 - reg: Physical base address and length of the controller's registers.
 - interrupts: The interrupt signal from the gpu.
-- clocks: device clocks
+- clocks: device clocks (if applicable)
   See ../clocks/clock-bindings.txt for details.
-- clock-names: the following clocks are required:
+- clock-names: the following clocks are required by a3xx, a4xx and a5xx
+  cores:
   * "core"
   * "iface"
   * "mem_iface"
+  For GMU attached devices the GPU clocks are not used and are not required. The
+  following devices should not list clocks:
+   - qcom,adreno-630.2
+- iommus: optional phandle to an adreno iommu instance
+- operating-points-v2: optional phandle to the OPP operating points
+- qcom,gmu: For GMU attached devices a phandle to the GMU device that will
+  control the power for the GPU. Applicable targets:
+    - qcom,adreno-630.2
 
-Example:
+Example 3xx/4xx/a5xx:
 
 / {
 	...

@@ -35,3 +44,30 @@ Example:
 		    <&mmcc MMSS_IMEM_AHB_CLK>;
 	};
 };
+
+Example a6xx (with GMU):
+
+/ {
+	...
+
+	gpu@5000000 {
+		compatible = "qcom,adreno-630.2", "qcom,adreno";
+		#stream-id-cells = <16>;
+
+		reg = <0x5000000 0x40000>, <0x509e000 0x10>;
+		reg-names = "kgsl_3d0_reg_memory", "cx_mem";
+
+		/*
+		 * Look ma, no clocks! The GPU clocks and power are
+		 * controlled entirely by the GMU
+		 */
+
+		interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>;
+
+		iommus = <&adreno_smmu 0>;
+
+		operating-points-v2 = <&gpu_opp_table>;
+
+		qcom,gmu = <&gmu>;
+	};
+};