From: Myl?ne Josserand <redacted>

The Nano Pi M1+ comes with an optional sensor based on the ov5640 from
Omnivision. Enable the support for it in the DT.

Signed-off-by: Myl?ne Josserand <redacted>
Signed-off-by: Maxime Ripard <redacted>
---
 arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts | 85 +++++++++++++++++++
 1 file changed, 85 insertions(+)

diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts b/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts
index 06010a9afba0..2ac62d109285 100644
--- a/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts
+++ b/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts

@@ -52,6 +52,37 @@
                ethernet1 = &sdio_wifi;
        };

+       cam_xclk: cam-xclk {
+                #clock-cells = <0>;
+                compatible = "fixed-clock";
+                clock-frequency = <24000000>;
+                clock-output-names = "cam-xclk";
+        };
+
+        reg_cam_avdd: cam-avdd {
+                compatible = "regulator-fixed";
+                regulator-name = "cam500b-avdd";
+                regulator-min-microvolt = <2800000>;
+                regulator-max-microvolt = <2800000>;
+                vin-supply = <&reg_vcc3v3>;
+        };
+
+        reg_cam_dovdd: cam-dovdd {
+                compatible = "regulator-fixed";
+                regulator-name = "cam500b-dovdd";
+                regulator-min-microvolt = <1800000>;
+                regulator-max-microvolt = <1800000>;
+                vin-supply = <&reg_vcc3v3>;
+        };
+
+        reg_cam_dvdd: cam-dvdd {
+                compatible = "regulator-fixed";
+                regulator-name = "cam500b-dvdd";
+                regulator-min-microvolt = <1500000>;
+                regulator-max-microvolt = <1500000>;
+                vin-supply = <&reg_vcc3v3>;
+        };
+
        reg_gmac_3v3: gmac-3v3 {
                compatible = "regulator-fixed";
                regulator-name = "gmac-3v3";

@@ -69,6 +100,26 @@
        };
 };

+&csi {
+        status = "okay";
+
+        port {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                /* Parallel bus endpoint */
+                csi_from_ov5640: endpoint {
+                        remote-endpoint = <&ov5640_to_csi>;
+                        bus-width = <8>;
+                        data-shift = <2>;
+                        hsync-active = <1>; /* Active high */
+                        vsync-active = <0>; /* Active low */
+                        data-active = <1>;  /* Active high */
+                        pclk-sample = <1>;  /* Rising */
+                };
+        };
+};
+
 &ehci1 {
        status = "okay";
 };

@@ -94,6 +145,40 @@
        };
 };

+&i2c2 {
+       status = "okay";
+
+       ov5640: camera at 3c {
+                compatible = "ovti,ov5640";
+                reg = <0x3c>;
+                clocks = <&cam_xclk>;