[PATCH v1 01/10] arm/arm64: dts: msm8974/msm8916: thermal: Split address space into two
From: Amit Kucheria <hidden>
Date: 2018-08-09 12:33:03
Also in:
linux-arm-msm, linux-devicetree, linux-pm, lkml
Subsystem:
arm/qualcomm mailing list, arm/qualcomm support, qualcomm tsens thermal driver, the rest, thermal · Maintainers:
Bjorn Andersson, Konrad Dybcio, Amit Kucheria, Thara Gopinath, Linus Torvalds, Rafael J. Wysocki, Daniel Lezcano
We've earlier added support to split the register address space into TM and SROT regions. Split up the regmap address space into two for the remaining platforms that have a similar register layout and make corresponding changes to the get_temp_common() function used by these platforms. Since tsens-common.c/init_common() currently only registers one address space, the order is important (TM before SROT). This is OK since the code doesn't really use the SROT functionality yet. Signed-off-by: Amit Kucheria <redacted> --- arch/arm/boot/dts/qcom-msm8974.dtsi | 6 ++++-- arch/arm64/boot/dts/qcom/msm8916.dtsi | 6 ++++-- drivers/thermal/qcom/tsens-common.c | 5 +++-- 3 files changed, 11 insertions(+), 6 deletions(-)
diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi
index d9019a49b292..3c4b81c29798 100644
--- a/arch/arm/boot/dts/qcom-msm8974.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8974.dtsi@@ -427,11 +427,13 @@ }; }; - tsens: thermal-sensor at fc4a8000 { + tsens: thermal-sensor at fc4a9000 { compatible = "qcom,msm8974-tsens"; - reg = <0xfc4a8000 0x2000>; + reg = <0xfc4a9000 0x1000>, /* TM */ + <0xfc4a8000 0x1000>; /* SROT */ nvmem-cells = <&tsens_calib>, <&tsens_backup>; nvmem-cell-names = "calib", "calib_backup"; + #qcom,sensors = <11>; #thermal-sensor-cells = <1>; };
diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi
index cc1040eacdf5..abf84df5a7bc 100644
--- a/arch/arm64/boot/dts/qcom/msm8916.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi@@ -774,11 +774,13 @@ }; }; - tsens: thermal-sensor at 4a8000 { + tsens: thermal-sensor at 4a9000 { compatible = "qcom,msm8916-tsens"; - reg = <0x4a8000 0x2000>; + reg = <0x4a9000 0x1000>, /* TM */ + <0x4a8000 0x1000>; /* SROT */ nvmem-cells = <&tsens_caldata>, <&tsens_calsel>; nvmem-cell-names = "calib", "calib_sel"; + #qcom,sensors = <5>; #thermal-sensor-cells = <1>; };
diff --git a/drivers/thermal/qcom/tsens-common.c b/drivers/thermal/qcom/tsens-common.c
index 6207d8d92351..478739543bbc 100644
--- a/drivers/thermal/qcom/tsens-common.c
+++ b/drivers/thermal/qcom/tsens-common.c@@ -21,7 +21,7 @@ #include <linux/regmap.h> #include "tsens.h" -#define S0_ST_ADDR 0x1030 +#define STATUS_OFFSET 0x30 #define SN_ADDR_OFFSET 0x4 #define SN_ST_TEMP_MASK 0x3ff #define CAL_DEGC_PT1 30
@@ -107,8 +107,9 @@ int get_temp_common(struct tsens_device *tmdev, int id, int *temp) unsigned int status_reg; int last_temp = 0, ret; - status_reg = S0_ST_ADDR + s->hw_id * SN_ADDR_OFFSET; + status_reg = tmdev->tm_offset + STATUS_OFFSET + s->hw_id * SN_ADDR_OFFSET; ret = regmap_read(tmdev->map, status_reg, &code); + if (ret) return ret; last_temp = code & SN_ST_TEMP_MASK;
--
2.17.1