[PATCH v3 15/19] arm64: dts: allwinner: a64: Olinuxino: enable USB
From: andre.przywara@arm.com (Andre Przywara)
Date: 2018-07-30 12:31:33
Subsystem:
arm/allwinner sunxi soc support, the rest · Maintainers:
Chen-Yu Tsai, Jernej Skrabec, Samuel Holland, Linus Torvalds
The Olinuxino has two USB sockets: USB0 is connected to a micro B socket. As it has the ID pin wired and the VBUS line connected to the PMIC, we describe it as a proper OTG socket, which switches between host and device automatically. USB1 is connected to a normal USB A socket. PG9 enables the power line, so add the required regulator as well. Signed-off-by: Andre Przywara <andre.przywara@arm.com> --- .../boot/dts/allwinner/sun50i-a64-olinuxino.dts | 45 ++++++++++++++++++++++ 1 file changed, 45 insertions(+)
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-olinuxino.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-olinuxino.dts
index 26075b9a76e3..a1c2f06ed474 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-olinuxino.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-olinuxino.dts@@ -59,12 +59,31 @@ stdout-path = "serial0:115200n8"; }; + reg_usb1_vbus: usb1-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb1-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + enable-active-high; + gpio = <&pio 6 9 GPIO_ACTIVE_HIGH>; /* PG9 */ + status = "okay"; + }; + wifi_pwrseq: wifi_pwrseq { compatible = "mmc-pwrseq-simple"; reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */ }; }; +&ehci0 { + status = "okay"; +}; + +&ehci1 { + status = "okay"; +}; + &emac { pinctrl-names = "default"; pinctrl-0 = <&rgmii_pins>;
@@ -109,6 +128,14 @@ }; }; +&ohci0 { + status = "okay"; +}; + +&ohci1 { + status = "okay"; +}; + &r_rsb { status = "okay";
@@ -117,6 +144,7 @@ reg = <0x3a3>; interrupt-parent = <&r_intc>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + x-powers,drive-vbus-en; /* set N_VBUSEN as output pin */ }; };
@@ -201,6 +229,11 @@ regulator-name = "vcc-wifi-io"; }; +®_drivevbus { + regulator-name = "usb0-vbus"; + status = "okay"; +}; + ®_eldo1 { regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>;
@@ -244,3 +277,15 @@ pinctrl-0 = <&uart0_pins_a>; status = "okay"; }; + +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + +&usbphy { + status = "okay"; + usb0_id_det-gpios = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */ + usb0_vbus-supply = <®_drivevbus>; + usb1_vbus-supply = <®_usb1_vbus>; +};
--
2.14.4