[PATCH 2/7] ARM: dts: s5pv210: Add initial DTS for Samsung Aries based phones.
From: krzk@kernel.org (Krzysztof Kozlowski)
Date: 2018-06-22 07:41:10
Also in:
linux-devicetree, linux-samsung-soc, lkml
On 21 June 2018 at 21:09, Pawe? Chmiel [off-list ref] wrote:
This DTS file have initial support Samsung Aries based phones. Initial version have support for: - sdcard - internal memory (present only on non 4g variant) - max8998 pmic and rtc - max17040 fuel gauge - gpio keys - fimd (no panel driver yet) - usb (peripherial mode) - wifi Signed-off-by: Pawe? Chmiel <redacted>
Hi Pawel, Nice job in mainlining! Below you'll find some comments for improvement.
quoted hunk ↗ jump to hunk
--- arch/arm/boot/dts/s5pv210-aries.dtsi | 397 +++++++++++++++++++++++++++++++++++ 1 file changed, 397 insertions(+) create mode 100644 arch/arm/boot/dts/s5pv210-aries.dtsidiff --git a/arch/arm/boot/dts/s5pv210-aries.dtsi b/arch/arm/boot/dts/s5pv210-aries.dtsi new file mode 100644 index 000000000000..6e8ac3615765 --- /dev/null +++ b/arch/arm/boot/dts/s5pv210-aries.dtsi@@ -0,0 +1,397 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Samsung's S5PV210 based Galaxy Aries board device tree source + */ + +/dts-v1/; +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/input/input.h>
Is the input header used here?
+#include <dt-bindings/interrupt-controller/irq.h>
Duplicated inclusion.
+#include "s5pv210.dtsi"
+
+/ {
+ compatible = "samsung,aries", "samsung,s5pv210";
+
+ aliases {
+ i2c6 = &i2c_pmic;
+ i2c9 = &i2c_fuel;
+ };
+
+ memory at 30000000 {
+ device_type = "memory";
+ reg = <0x30000000 0x05000000
+ 0x40000000 0x10000000
+ 0x50000000 0x08000000>;
+ };
+
+ wifi_pwrseq: wifi-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&gpg1 2 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&wlan_gpio_rst>;
+ post-power-on-delay-ms = <500>;
+ power-off-delay-us = <500>;
+ };
+
+ i2c_pmic: i2c-pmic {s/i2c-pmic/ to /i2c-gpio-0/ to reflect generic class of this node. Change only the node name. The label can stay as is.
+ compatible = "i2c-gpio"; + sda-gpios = <&gpj4 0 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpj4 3 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
Spaces around pipe |.
+ i2c-gpio,delay-us = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pmic at 66 {
+ compatible = "maxim,max8998";
+ reg = <0x66>;
+ interrupt-parent = <&gph0>;
+ interrupts = <7 0>;If you really wanted 0 then IRQ_TYPE_NONE... but this should be a proper interrupt type.
+
+ max8998,pmic-buck1-default-dvs-idx = <1>;
+ max8998,pmic-buck1-dvs-gpios = <&gph0 3 GPIO_ACTIVE_HIGH>,
+ <&gph0 4 GPIO_ACTIVE_HIGH>;
+ max8998,pmic-buck1-dvs-voltage = <1275000>, <1200000>,
+ <1050000>, <950000>;
+
+ max8998,pmic-buck2-default-dvs-idx = <0>;
+ max8998,pmic-buck2-dvs-gpio = <&gph0 5 GPIO_ACTIVE_HIGH>;
+ max8998,pmic-buck2-dvs-voltage = <1100000>, <1000000>;
+
+ regulators {
+ ldo2_reg: LDO2 {
+ regulator-name = "VALIVE_1.2V";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ ldo3_reg: LDO3 {
+ regulator-name = "VUSB_1.1V";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo4_reg: LDO4 {
+ regulator-name = "VADC_3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo5_reg: LDO5 {
+ regulator-name = "VTF_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };LDO6? All regulators should be defined in general. Most of the drivers would anyway register all of them and use driver-specific defaults for the ones which are missing in DT. I see that max8998 behaves differently and silently ignores missing regulators leaving them at bootloader settings. That's also not good because their initial settings might not be correct for current load and kernel cannot turn them off if needed. Also we want in general to have full description of HW in DT. The same applies to LDO10, clocks and ESAFEOUT2 later.
+
+ ldo7_reg: LDO7 {
+ regulator-name = "VLCD_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ /* Till we get panel driver */
+ regulator-always-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo8_reg: LDO8 {
+ regulator-name = "VUSB_3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo9_reg: LDO9 {
+ regulator-name = "VCC_2.8V_PDA";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ };
+
+ ldo11_reg: LDO11 {
+ regulator-name = "CAM_AF_3.0V";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo12_reg: LDO12 {
+ regulator-name = "CAM_SENSOR_CORE_1.2V";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo13_reg: LDO13 {
+ regulator-name = "VGA_VDDIO_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo14_reg: LDO14 {
+ regulator-name = "VGA_DVDD_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo15_reg: LDO15 {
+ regulator-name = "CAM_ISP_HOST_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo16_reg: LDO16 {
+ regulator-name = "VGA_AVDD_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo17_reg: LDO17 {
+ regulator-name = "VCC_3.0V_LCD";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ /* Till we get panel driver */
+ regulator-always-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ buck1_reg: BUCK1 {
+ regulator-name = "vddarm";
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1500000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <1250000>;
+ };
+ };
+
+ buck2_reg: BUCK2 {
+ regulator-name = "vddint";
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1500000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <1100000>;
+ };
+ };
+
+ buck3_reg: BUCK3 {
+ regulator-name = "VCC_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ buck4_reg: BUCK4 {
+ regulator-name = "CAM_ISP_CORE_1.2V";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ safe1_sreg: ESAFEOUT1 {
+ regulator-name = "SAFEOUT1";
+ };
+ };
+ };
+ };
+
+ i2c_fuel: i2c-fuel {s/i2c-fuel/ to /i2c-gpio-1/
+ compatible = "i2c-gpio"; + sda-gpios = <&mp05 1 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + scl-gpios = <&mp05 0 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
Spaces around | please.
+ i2c-gpio,delay-us = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fuel at 36 {Name: fuelgauge
+ compatible = "maxim,max17040";
+ interrupt-parent = <&vic0>;
+ interrupts = <7>;
+ reg = <0x36>;
+ };
+ };
+};
+
+&xusbxti {
+ clock-frequency = <24000000>;
+};
+
+&pinctrl0 {Please order all labels alphabetically. It reduces conflicts later with multiple changes.
+ wlan_bt_en: wlan-bt-en {
+ samsung,pins = "gpb-5";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+ samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
+ samsung,pin-val = <1>;
+ };
+
+ wlan_gpio_rst: wlan-gpio-rst {
+ samsung,pins = "gpg1-2";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+ samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
+ };
+
+ wifi_host_wake: wifi-host-wake {
+ samsung,pins = "gph2-4";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+ samsung,pin-pud = <S3C64XX_PIN_PULL_DOWN>;
+ samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+ };
+
+ tf_detect: tf-detect {
+ samsung,pins = "gph3-4";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+ samsung,pin-pud = <S3C64XX_PIN_PULL_DOWN>;
+ samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+ };
+
+ wifi_wake: wifi-wake {
+ samsung,pins = "gph3-5";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+ samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
+ };
+
+ massmemory_en: massmemory-en {
+ samsung,pins = "gpj2-7";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+ samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
+ samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&sdhci1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ bus-width = <4>;
+ max-frequency = <38400000>;
+ pinctrl-0 = <&sd1_clk &sd1_cmd &sd1_bus4 &wifi_wake &wifi_host_wake &wlan_bt_en>;
+ pinctrl-names = "default";
+ cap-sd-highspeed;
+ cap-mmc-highspeed;
+
+ mmc-pwrseq = <&wifi_pwrseq>;
+ non-removable;
+ status = "okay";
+
+ brcmf: bcrmf at 1 {Name of node should describe generic class of the device so maybe "wlan" or "wlanbt"? Label is okay. Best regards, Krzysztof