Anson Huang
Best Regards!

-----Original Message-----
From: Fabio Estevam [mailto:festevam at gmail.com]
Sent: Sunday, February 11, 2018 12:26 AM
To: Stefan Agner <stefan@agner.ch>; Anson Huang <redacted>
Cc: rjw at rjwysocki.net; viresh kumar <viresh.kumar@linaro.org>;
linux-pm at vger.kernel.org; Marcel Ziswiler [off-list ref];
max.oss.09 at gmail.com; linux-kernel [off-list ref]; Octavian
Purdila [off-list ref]; Fabio Estevam
[off-list ref]; Shawn Guo [off-list ref]; moderated
list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE
[off-list ref]; dl-linux-imx [off-list ref]
Subject: Re: [PATCH] cpufreq: imx6q: support frequencies >528MHz for
i.MX6UL/ULL

Hi Anson,

On Thu, Jan 18, 2018 at 9:58 PM, Stefan Agner [off-list ref] wrote:

quoted

Depending on SKU i.MX6UL/i.MX6ULL support frequencies up to 900MHz.
Use PLL1 sys clock for all operating points higher than 528MHz.

Note: For higher operating points VDD_SOC_IN needs to be 125mV higher
than the ARM set-point (see datasheet). Specifically, the i.MX6UL/ULL
EVK boards have an external DC regulator which needs adjustment. The
regulator adjustment is not covered with this change.

Signed-off-by: Stefan Agner <stefan@agner.ch>
---
 drivers/cpufreq/imx6q-cpufreq.c | 14 ++++++++------
 1 file changed, 8 insertions(+), 6 deletions(-)

diff --git a/drivers/cpufreq/imx6q-cpufreq.c

b/drivers/cpufreq/imx6q-cpufreq.c index 628fe899cb48..840f6386c780
100644

--- a/drivers/cpufreq/imx6q-cpufreq.c
+++ b/drivers/cpufreq/imx6q-cpufreq.c

@@ -114,12 +114,14 @@ static int imx6q_set_target(struct cpufreq_policy

*policy, unsigned int index)

quoted

                 */
                clk_set_rate(arm_clk, (old_freq >> 1) * 1000);
                clk_set_parent(pll1_sw_clk, pll1_sys_clk);
-               if (freq_hz > clk_get_rate(pll2_pfd2_396m_clk))
-                       clk_set_parent(secondary_sel_clk, pll2_bus_clk);
-               else
-                       clk_set_parent(secondary_sel_clk,

pll2_pfd2_396m_clk);

quoted

-               clk_set_parent(step_clk, secondary_sel_clk);
-               clk_set_parent(pll1_sw_clk, step_clk);
+               if (freq_hz <= clk_get_rate(pll2_bus_clk)) {
+                       if (freq_hz > clk_get_rate(pll2_pfd2_396m_clk))
+                               clk_set_parent(secondary_sel_clk,

pll2_bus_clk);

quoted

+                       else
+                               clk_set_parent(secondary_sel_clk,

pll2_pfd2_396m_clk);

quoted

+                       clk_set_parent(step_clk, secondary_sel_clk);
+                       clk_set_parent(pll1_sw_clk, step_clk);
+               }

For cpufreq > 528MHz, ARM PLL needs to be set_rate, I did NOT see where sets ARM PLL rate?

Anson.

quoted

        } else {
                clk_set_parent(step_clk, pll2_pfd2_396m_clk);
                clk_set_parent(pll1_sw_clk, step_clk);

Could you please help reviewing this patch?

Thanks