[PATCH v2 02/16] mmc: sdhci-omap: Add card_busy host ops
From: Kishon Vijay Abraham I <hidden>
Date: 2018-02-05 12:51:54
Also in:
linux-devicetree, linux-mmc, linux-omap, lkml
Subsystem:
multimedia card (mmc), secure digital (sd) and sdio subsystem, secure digital host controller interface (sdhci) driver, secure digital host controller interface (sdhci) ti omap driver, the rest · Maintainers:
Ulf Hansson, Adrian Hunter, Vignesh Raghavendra, Linus Torvalds
Add card_busy host ops in sdhci_omap to check card busy status. The voltage switching sequence for AM572x platform is mentioned in Figure 25-48. eMMC/SD/SDIO Power Switching Procedure of AM572x Sitara Processors Silicon Revision 2.0, 1.1 TRM (SPRUHZ6I - October 2014?Revised April 2017 [1]). In the voltage switching sequence, CLKEXTFREE bit in MMCHS_CON should also be set after switching to 1.8v which is also taken care in the card_busy ops. [1] -> http://www.ti.com/lit/ug/spruhz6i/spruhz6i.pdf Signed-off-by: Kishon Vijay Abraham I <redacted> --- drivers/mmc/host/sdhci-omap.c | 52 +++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 52 insertions(+)
diff --git a/drivers/mmc/host/sdhci-omap.c b/drivers/mmc/host/sdhci-omap.c
index 96985786cadf..df927f3faaf6 100644
--- a/drivers/mmc/host/sdhci-omap.c
+++ b/drivers/mmc/host/sdhci-omap.c@@ -31,11 +31,17 @@ #define SDHCI_OMAP_CON 0x12c #define CON_DW8 BIT(5) #define CON_DMA_MASTER BIT(20) +#define CON_CLKEXTFREE BIT(16) +#define CON_PADEN BIT(15) #define CON_INIT BIT(1) #define CON_OD BIT(0) #define SDHCI_OMAP_CMD 0x20c +#define SDHCI_OMAP_PSTATE 0x0224 +#define PSTATE_DLEV_DAT0 BIT(20) +#define PSTATE_DATI BIT(1) + #define SDHCI_OMAP_HCTL 0x228 #define HCTL_SDBP BIT(8) #define HCTL_SDVS_SHIFT 9
@@ -191,6 +197,51 @@ static void sdhci_omap_conf_bus_power(struct sdhci_omap_host *omap_host, } } +static int sdhci_omap_card_busy(struct mmc_host *mmc) +{ + u32 reg, ac12; + int ret = false; + struct sdhci_host *host = mmc_priv(mmc); + struct sdhci_pltfm_host *pltfm_host; + struct sdhci_omap_host *omap_host; + u32 ier = host->ier; + + pltfm_host = sdhci_priv(host); + omap_host = sdhci_pltfm_priv(pltfm_host); + + reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_CON); + ac12 = sdhci_omap_readl(omap_host, SDHCI_OMAP_AC12); + reg &= ~CON_CLKEXTFREE; + if (ac12 & AC12_V1V8_SIGEN) + reg |= CON_CLKEXTFREE; + reg |= CON_PADEN; + sdhci_omap_writel(omap_host, SDHCI_OMAP_CON, reg); + + disable_irq(host->irq); + ier |= SDHCI_INT_CARD_INT; + sdhci_writel(host, ier, SDHCI_INT_ENABLE); + sdhci_writel(host, ier, SDHCI_SIGNAL_ENABLE); + + /* + * Delay is required for PSTATE to correctly reflect + * DLEV/CLEV values after PADEN is set. + */ + usleep_range(50, 100); + reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_PSTATE); + if ((reg & PSTATE_DATI) || !(reg & PSTATE_DLEV_DAT0)) + ret = true; + + reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_CON); + reg &= ~(CON_CLKEXTFREE | CON_PADEN); + sdhci_omap_writel(omap_host, SDHCI_OMAP_CON, reg); + + sdhci_writel(host, host->ier, SDHCI_INT_ENABLE); + sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE); + enable_irq(host->irq); + + return ret; +} + static int sdhci_omap_start_signal_voltage_switch(struct mmc_host *mmc, struct mmc_ios *ios) {
@@ -562,6 +613,7 @@ static int sdhci_omap_probe(struct platform_device *pdev) host->mmc_host_ops.start_signal_voltage_switch = sdhci_omap_start_signal_voltage_switch; host->mmc_host_ops.set_ios = sdhci_omap_set_ios; + host->mmc_host_ops.card_busy = sdhci_omap_card_busy; sdhci_read_caps(host); host->caps |= SDHCI_CAN_DO_ADMA2;
--
2.11.0