Re: [PATCH v6 00/41] ARM: davinci: convert to common clock framework​

On Thursday 25 January 2018 09:48 PM, David Lechner wrote:

On 01/25/2018 06:53 AM, Sekhar Nori wrote:

quoted

On Wednesday 24 January 2018 01:33 PM, Bartosz Golaszewski wrote:

quoted

2018-01-23 21:23 GMT+01:00 David Lechner [off-list ref]:

quoted

On 01/23/2018 02:05 PM, David Lechner wrote:

quoted

On 01/23/2018 02:01 PM, David Lechner wrote:

quoted

On 01/23/2018 01:53 PM, Bartosz Golaszewski wrote:

quoted

In the mdio case - the problem is that devm_clk_get() doesn't fail,
but somehow the clock doesn't end up in the list of the device's
clocks - which is why it's not enabled by pm_runtime_get_sync().

Right. This is because devm_clk_get() now finds the clock via device
tree instead of a clkdev lookup entry. However, I think that the PM
notifier registered in arch/arm/mach-davinci/pm_domain.c only uses
the clkdev lookup to match the con_id and does not use device tree.
The same thing is happing in mdio, emac and lcdc.

Minor correction: It looks like emac doesn't do this because it
doesn't
have a con_id of "fck". But, the same clock is shared by emac and
mdio, so
since mdio enables the clock, emac doesn't notice or care that it did
not enable the clock itself.

How about using pm_clk_add_clk() in these drivers to explicitly use the
clocks for power management instead of relying on pm_clk_add_notifier()
to do this implicitly?

Yes, this sounds good.

Looking at how pm_clk_notify() in clock_ops.c uses con_id[] list, right
now pm_runtime() will work only for clocks which have con_id (from the
list above) mentioned in DT. Since clk_find() mandates con_id match when
its available, NULL con_id does not match.

For simple devices like DaVinci which uses just one clock for power
management per device (multiple devices might share a clock, but not
other way around as far as I recall, anyway I will double check this
assertion), the attached patch should make EMAC work.

That still leaves why lcdc does not work. One difference is it uses
PSC1. Are there other devices in PSC1 which work (just to rule out any
thing wrong with PSC1 handling).

Thanks,
Sekhar

---8<---

diff --git a/arch/arm/mach-davinci/pm_domain.c

b/arch/arm/mach-davinci/pm_domain.c
index 78eac2c0c146..0dce7397856d 100644

--- a/arch/arm/mach-davinci/pm_domain.c
+++ b/arch/arm/mach-davinci/pm_domain.c

@@ -23,7 +23,6 @@ static struct dev_pm_domain davinci_pm_domain = {

? ? static struct pm_clk_notifier_block platform_bus_notifier = {
????? .pm_domain = &davinci_pm_domain,
-??? .con_ids = { "fck", "master", "slave", NULL },
? };
? ? static int __init davinci_pm_runtime_init(void)

Won't this cause *all* clocks, not just PSC clocks, to be used for power
management?

In case of DT, the first clock mentioned in 'clocks' property will get
picked up since it will match with wildcard con_id. This unfortunately
depends on how the clocks list is prepared so quite implementation
dependent.

Some examples of devices with more than just the PSC clock are SATA and
the USB PHY.

Its not a problem to have more than one clock passed in device node as
long as only one clock (the first clock) needs to participate in power
management.

This may work for the moment, but longer term I do think genpd
implementation for DaVinci will be needed. Or may be there is breakage
even today that I am not able to think on top of my head.

Thanks,
Sekhar