[linux-sunxi] [PATCH v4 1/2] dt-bindings: media: Add Allwinner V3s Camera Sensor Interface (CSI)

On Fri, 22 Dec 2017 10:00:08 +0000
Priit Laes [off-list ref] wrote:

On Fri, Dec 22, 2017 at 05:41:29PM +0800, Yong Deng wrote:

quoted

Add binding documentation for Allwinner V3s CSI.

Signed-off-by: Yong Deng <yong.deng@magewell.com>
---
 .../devicetree/bindings/media/sun6i-csi.txt        | 51 ++++++++++++++++++++++
 1 file changed, 51 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/sun6i-csi.txt

diff --git a/Documentation/devicetree/bindings/media/sun6i-csi.txt b/Documentation/devicetree/bindings/media/sun6i-csi.txt
new file mode 100644
index 0000000..b5bfe3f
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/sun6i-csi.txt

@@ -0,0 +1,51 @@
+Allwinner V3s Camera Sensor Interface
+------------------------------

Not sure whether syntax for these files is proper reStructuredText/Markdown,
but the underline-ish style expects the title and underline having same length.

OK.

quoted

+
+Required properties:
+  - compatible: value must be "allwinner,sun8i-v3s-csi"
+  - reg: base address and size of the memory-mapped region.
+  - interrupts: interrupt associated to this IP
+  - clocks: phandles to the clocks feeding the CSI
+    * bus: the CSI interface clock
+    * mod: the CSI module clock
+    * ram: the CSI DRAM clock
+  - clock-names: the clock names mentioned above
+  - resets: phandles to the reset line driving the CSI
+
+- ports: A ports node with endpoint definitions as defined in
+  Documentation/devicetree/bindings/media/video-interfaces.txt.
+  Currently, the driver only support the parallel interface. So, a single port

^^ supports

quoted

+  node with one endpoint and parallel bus is supported.
+
+Example:
+
+	csi1: csi at 1cb4000 {
+		compatible = "allwinner,sun8i-v3s-csi";
+		reg = <0x01cb4000 0x1000>;
+		interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&ccu CLK_BUS_CSI>,
+			 <&ccu CLK_CSI1_SCLK>,
+			 <&ccu CLK_DRAM_CSI>;
+		clock-names = "bus", "mod", "ram";
+		resets = <&ccu RST_BUS_CSI>;
+
+		port {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			/* Parallel bus endpoint */
+			csi1_ep: endpoint {
+				remote-endpoint = <&adv7611_ep>;
+				bus-width = <16>;
+				data-shift = <0>;
+
+				/* If hsync-active/vsync-active are missing,
+				   embedded BT.656 sync is used */
+				hsync-active = <0>; /* Active low */
+				vsync-active = <0>; /* Active low */
+				data-active = <1>;  /* Active high */
+				pclk-sample = <1>;  /* Rising */
+			};
+		};
+	};
+
-- 
1.8.3.1

-- 
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe at googlegroups.com.
For more options, visit https://groups.google.com/d/optout.

-- 
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe at googlegroups.com.
For more options, visit https://groups.google.com/d/optout.

Thanks,
Yong