@@ -2534,10 +2534,29 @@ CONFIG_ARCH_HAS_DEVMEM_IS_ALLOWED=y
 # CONFIG_ARM_PTDUMP is not set
 # CONFIG_ARM_UNWIND is not set
 # CONFIG_DEBUG_USER is not set
-# CONFIG_DEBUG_LL is not set
-CONFIG_DEBUG_LL_INCLUDE="mach/debug-macro.S"
+CONFIG_DEBUG_LL=y
+# CONFIG_DEBUG_OMAP2UART1 is not set
+# CONFIG_DEBUG_OMAP2UART2 is not set
+# CONFIG_DEBUG_OMAP2UART3 is not set
+CONFIG_DEBUG_OMAP3UART3=y
+# CONFIG_DEBUG_OMAP4UART3 is not set
+# CONFIG_DEBUG_OMAP3UART4 is not set
+# CONFIG_DEBUG_OMAP4UART4 is not set
+# CONFIG_DEBUG_TI81XXUART1 is not set
+# CONFIG_DEBUG_TI81XXUART2 is not set
+# CONFIG_DEBUG_TI81XXUART3 is not set
+# CONFIG_DEBUG_AM33XXUART1 is not set
+# CONFIG_DEBUG_ZOOM_UART is not set
+# CONFIG_DEBUG_ICEDCC is not set
+# CONFIG_DEBUG_SEMIHOSTING is not set
+# CONFIG_DEBUG_LL_UART_8250 is not set
+# CONFIG_DEBUG_LL_UART_PL01X is not set
+CONFIG_DEBUG_OMAP2PLUS_UART=y
+CONFIG_DEBUG_LL_INCLUDE="debug/omap2plus.S"
 # CONFIG_DEBUG_UART_8250 is not set
+CONFIG_DEBUG_UNCOMPRESS=y
 CONFIG_UNCOMPRESS_INCLUDE="debug/uncompress.h"
+CONFIG_EARLY_PRINTK=y
 # CONFIG_PID_IN_CONTEXTIDR is not set
 # CONFIG_CORESIGHT is not set
 

@@ -1736,7 +1736,7 @@ config DEBUG_UART_8250_FLOW_CONTROL
 config DEBUG_UNCOMPRESS
 	bool
 	depends on ARCH_MULTIPLATFORM || PLAT_SAMSUNG || ARM_SINGLE_ARMV7M
-	default y if DEBUG_LL && !DEBUG_OMAP2PLUS_UART && \
+	default y if DEBUG_LL && (!DEBUG_OMAP2PLUS_UART || !ZROM_BOOT) && \
 		     (!DEBUG_TEGRA_UART || !ZBOOT_ROM) && \
 		     !DEBUG_BRCMSTB_UART
 	help

@@ -58,12 +58,17 @@
 
 #define UART_OFFSET(addr)	((addr) & 0x00ffffff)
 
+#if defined(ZIMAGE)
+	omap_uart_phys:	.word	0
+	omap_uart_virt:	.word	0
+	omap_uart_lsr:	.word	0
+#else
 		.pushsection .data
-omap_uart_phys:	.word	0
-omap_uart_virt:	.word	0
-omap_uart_lsr:	.word	0
+	omap_uart_phys:	.word	0
+	omap_uart_virt:	.word	0
+	omap_uart_lsr:	.word	0
 		.popsection
-
+#endif
 		.macro	addruart, rp, rv, tmp
 
 		/* Use omap_uart_phys/virt if already configured */

@@ -1,7 +1,109 @@
-#ifdef CONFIG_DEBUG_UNCOMPRESS
-extern void putc(int c);
-#else
-static inline void putc(int c) {}
-#endif
-static inline void flush(void) {}
-static inline void arch_decomp_setup(void) {}
+/*
+ * arch/arm/plat-omap/include/mach/uncompress.h
+ *
+ * Serial port stubs for kernel decompress status messages
+ *
+ * Initially based on:
+ * linux-2.4.15-rmk1-dsplinux1.6/arch/arm/plat-omap/include/mach1510/uncompress.h
+ * Copyright (C) 2000 RidgeRun, Inc.
+ * Author: Greg Lonnon <glonnon@ridgerun.com>
+ *
+ * Rewritten by:
+ * Author: <source@mvista.com>
+ * 2004 (c) MontaVista Software, Inc.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#include <linux/types.h>
+#include <linux/serial_reg.h>
+
+#include <asm/memory.h>
+#include <asm/mach-types.h>
+
+//#include <mach/serial.h>
+
+#define OMAP_UART_INFO_OFS 0x3ffc
+
+#define MDR1_MODE_MASK			0x07
+
+volatile u8 *uart_base;
+int uart_shift;
+
+/*
+ * Store the DEBUG_LL uart number into memory.
+ * See also debug-macro.S, and serial.c for related code.
+ */
+static void set_omap_uart_info(unsigned char port)
+{
+	/*
+	 * Get address of some.bss variable and round it down
+	 * a la CONFIG_AUTO_ZRELADDR.
+	 */
+	u32 ram_start = (u32)&uart_shift & 0xf8000000;
+	u32 *uart_info = (u32 *)(ram_start + OMAP_UART_INFO_OFS);
+	*uart_info = port;
+}
+
+static inline void putc(int c)
+{
+	if (!uart_base)
+		return;
+
+	/* Check for UART 16x mode */
+	if ((uart_base[UART_OMAP_MDR1 << uart_shift] & MDR1_MODE_MASK) != 0)
+		return;
+
+	while (!(uart_base[UART_LSR << uart_shift] & UART_LSR_THRE))
+		barrier();
+	uart_base[UART_TX << uart_shift] = c;
+}
+
+static inline void flush(void)
+{
+}
+
+/*
+ * Macros to configure UART1 and debug UART
+ */
+#define _DEBUG_LL_ENTRY(mach, dbg_uart, dbg_shft, dbg_id)		\
+	if (1) {					\
+		uart_base = (volatile u8 *)(dbg_uart);			\
+		uart_shift = (dbg_shft);				\
+		port = (dbg_id);					\
+		set_omap_uart_info(port);				\
+		break;							\
+	}
+
+#define DEBUG_LL_OMAP7XX(p, mach)					\
+	_DEBUG_LL_ENTRY(mach, OMAP1_UART##p##_BASE, OMAP7XX_PORT_SHIFT,	\
+		OMAP1UART##p)
+
+#define DEBUG_LL_OMAP1(p, mach)						\
+	_DEBUG_LL_ENTRY(mach, OMAP1_UART##p##_BASE, OMAP_PORT_SHIFT,	\
+		OMAP1UART##p)
+
+#define DEBUG_LL_OMAP3(p, mach)                                         \
+	_DEBUG_LL_ENTRY(mach, OMAP3_UART##p##_BASE, OMAP_PORT_SHIFT,    \
+			OMAP3UART##p)
+
+#define OMAP3_UART3_BASE 0x49020000
+#define OMAP_PORT_SHIFT 2
+#define OMAP3UART3 33
+
+static inline void arch_decomp_setup(void)
+{
+	int port = 0;
+
+	/*
+	 * Initialize the port based on the machine ID from the bootloader.
+	 * Note that we're using macros here instead of switch statement
+	 * as machine_is functions are optimized out for the boards that
+	 * are not selected.
+	 */
+	do {
+		DEBUG_LL_OMAP3(3, nokia_rm680);
+	} while (0);
+}

@@ -14,6 +14,7 @@
  */
 #include <linux/kernel.h>
 #include <linux/init.h>
+#include <linux/gpio.h>
 
 #include "common.h"
 #include "omap-secure.h"

@@ -32,3 +33,20 @@ void __init omap_reserve(void)
 	omap_secure_ram_reserve_memblock();
 	omap_barrier_reserve_memblock();
 }
+
+void iam_alive(void)
+{
+	int i;
+	int debug_gpio = 92;
+	printk("request: %d\n", gpio_request(debug_gpio, "debug"));
+	printk("output: %d\n", gpio_direction_output(debug_gpio, 1));
+
+	for (i=0; i<5; i++) {
+		gpio_set_value(debug_gpio, 0);
+		msleep(1000);
+		gpio_set_value(debug_gpio, 1);
+		msleep(1000);
+	}
+	
+}
+

@@ -118,6 +118,10 @@ static void omap2_show_dma_caps(void)
 	u8 revision = dma_read(REVISION, 0) & 0xff;
 	printk(KERN_INFO "OMAP DMA hardware revision %d.%d\n",
 				revision >> 4, revision & 0xf);
+       {
+              extern void iam_alive(void);
+               iam_alive();
+      }
 }
 
 static unsigned configure_dma_errata(void)