[PATCH 1/3] dt-bindings: Add document for rockchip RGB output interface
From: robh@kernel.org (Rob Herring)
Date: 2017-09-19 14:46:27
Also in:
dri-devel, linux-devicetree, linux-rockchip, lkml
On Thu, Sep 14, 2017 at 11:43:18AM +0800, Sandy Huang wrote:
quoted hunk ↗ jump to hunk
This path add support rv1108 rgb output interface driver. Signed-off-by: Sandy Huang <hjc@rock-chips.com> --- .../bindings/display/rockchip/rockchip-rgb.txt | 80 ++++++++++++++++++++++ 1 file changed, 80 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/rockchip/rockchip-rgb.txtdiff --git a/Documentation/devicetree/bindings/display/rockchip/rockchip-rgb.txt b/Documentation/devicetree/bindings/display/rockchip/rockchip-rgb.txt new file mode 100644 index 0000000..4164512 --- /dev/null +++ b/Documentation/devicetree/bindings/display/rockchip/rockchip-rgb.txt@@ -0,0 +1,80 @@ +Rockchip RV1108 RGB interface +================================ + +Required properties: +- compatible: matching the soc type: + - "rockchip,rv1108-rgb"; + +Optional properties: +- pinctrl-names: must contain a "lcdc" entry. +- pinctrl-0: pin control group to be used for this interface. + +Required nodes: +- rockchip,rgb-mode: should be "p888", "p666", "p565", "s888", "s888-dummy"
This should be a standard property. Any device with a parallel interface is going to need something like this.
+ - p888: output r8-g8-b8 at each dclk cycle for per-pixel
+ - p666: output r6-g6-b6 at each dclk cycle for per-pixel
+ - p565: output r5-g6-b5 at each dclk cycle for per-pixel
+ - s888: output r8-g8-b8 in three dclk cycle for per-pixel
+ - s888-dmmy: output r8-g8-b8-dummy in four dclk cycle for per-pixel
+
+The rgb has two video ports described by:
+ Documentation/devicetree/bindings/media/video-interfaces.txt
+Their connections are modeled using the OF graph bindings specified in
+ Documentation/devicetree/bindings/graph.txt.
+
+- video port 0 for the VOP input, the remote endpoint maybe vopb/vopl/vop
+- video port 1 for either a panel or subsequent encoder
+
+the panel described by:
+ Documentation/devicetree/bindings/display/panel/simple-panel.txt
+Panel other required properties:
+- ports for remote rgb output.
+
+Example:
+
+panel: panel {
+ compatible = "auo,b101ean01";
+ enable-gpios = <&gpio7 21 GPIO_ACTIVE_HIGH>;
+
+ ports {
+ panel_in_rgb: endpoint {
+ remote-endpoint = <&rgb_out_panel>;
+ };
+ };
+};
+
+For Rockchip RV1108:
+
+ rgb: rgb {
+ compatible = "rockchip,rv1108-rgb";
+ pinctrl-names = "lcdc";
+ pinctrl-0 = <&lcdc_ctl>;
+ rockchip,rgb-mode = "p888";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ rgb_in: port at 0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ rgb_in_vop: endpoint at 0 {
+ reg = <0>;Don't need reg for a single endpoint.
+ remote-endpoint = <&vop_out_rgb>;
+ };
+ };
+
+ rgb_out: port at 1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ rgb_out_panel: endpoint at 0 {
+ reg = <0>;ditto.
+ remote-endpoint = <&panel_in_rgb>; + }; + }; + }; + }; -- 2.7.4