[PATCH 3/3] ARM: dts: bcm2835: Add Raspberry Pi Zero W

Am 26.07.2017 um 22:09 schrieb Eric Anholt:

Stefan Wahren [off-list ref] writes:

quoted

The Raspberry Pi Zero W has the same components like the Zero plus
a Cypress CYW43438 wireless chip (wifi + bl).

I sent out v2 of the arm64 patch so that hopefully we can get started
merging this.  Couple of comments on a re-read.

quoted

Signed-off-by: Stefan Wahren <redacted>
Reviewed-by: Eric Anholt <redacted>
---
 arch/arm/boot/dts/Makefile               |  3 +-
 arch/arm/boot/dts/bcm2835-rpi-zero-w.dts | 73 ++++++++++++++++++++++++++++++++
 2 files changed, 75 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/boot/dts/bcm2835-rpi-zero-w.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index ec60f4f..f3bf9397 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile

@@ -74,7 +74,8 @@ dtb-$(CONFIG_ARCH_BCM2835) += \
 	bcm2835-rpi-a-plus.dtb \
 	bcm2836-rpi-2-b.dtb \
 	bcm2837-rpi-3-b.dtb \
-	bcm2835-rpi-zero.dtb
+	bcm2835-rpi-zero.dtb \
+	bcm2835-rpi-zero-w.dtb
 dtb-$(CONFIG_ARCH_BCM_5301X) += \
 	bcm4708-asus-rt-ac56u.dtb \
 	bcm4708-asus-rt-ac68u.dtb \

diff --git a/arch/arm/boot/dts/bcm2835-rpi-zero-w.dts b/arch/arm/boot/dts/bcm2835-rpi-zero-w.dts
new file mode 100644
index 0000000..9c6d714
--- /dev/null
+++ b/arch/arm/boot/dts/bcm2835-rpi-zero-w.dts

@@ -0,0 +1,73 @@
+/*
+ * Copyright (C) 2017 Stefan Wahren <stefan.wahren@i2se.com>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include "bcm2835.dtsi"
+#include "bcm2835-rpi.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+
+/ {
+	compatible = "raspberrypi,model-zero-w", "brcm,bcm2835";
+	model = "Raspberry Pi Zero W";
+
+	aliases {
+		uart0 = "/soc/serial at 7e201000";
+		uart1 = "/soc/serial at 7e215040";
+		serial0 = "/soc/serial at 7e201000";
+		serial1 = "/soc/serial at 7e215040";
+	};

Should we have this in the other board DTs?  What does it do?

This was the hardest part to make the Zero W useable. I took it from
downstream [1], because without it i don't see anything on debug UART
(config.txt already has enable_uart=1).

I could add a helpful comment, but i can't explain why it's necessary
for RPI Zero W and not for the older RPI Zero.

Maybe the foundation guys have an alternative solution or at least
explanation.

[1] -
https://github.com/raspberrypi/linux/blob/rpi-4.9.y/arch/arm/boot/dts/bcm2708-rpi.dtsi
[2] -
https://github.com/raspberrypi/linux/blob/rpi-4.9.y/arch/arm/boot/dts/overlays/pi3-disable-bt-overlay.dts

quoted

+
+	leds {
+		act {
+			gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wl_on>;
+		reset-gpios = <&gpio 41 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&gpio {
+	pinctrl-0 = <&gpioout &alt0>;
+
+	wl_on: wl-on {
+		brcm,pins = <41>;
+		brcm,function = <BCM2835_FSEL_GPIO_OUT>;
+	};
+};

Would you be up for adding gpio-line-names based on the dt-blob.dts?

Sure

quoted

+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+};
+
+&sdhci {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-0 = <&emmc_gpio34 &gpclk2_gpio43>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	non-removable;
+	status = "okay";
+
+	brcmf: wifi at 1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_gpio14>;
+	status = "okay";
+};
-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel at lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel