[PATCH v3 0/5] Add SoM1 support

On Thu, Jul 06, 2017 at 02:29:36PM +0200, Nicolas Ferre wrote:

On 06/07/2017 at 10:35, Claudiu Beznea wrote:

quoted

Hi all,

This series adds support for sama5d2 SoM1 devices.

The at91-sama5d27_som1.dtsi add specific bindings for SoM1 board.
The at91-sama5d27_som1_ek.dts add specific bindings for SoM1 EK board.

Thank you,
Claudiu

You can add my:
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>

for the whole series.
(I remember that we also had Ludovic's one as well).

Yes, the only comment was about the mac-offset but it has been removed
from this series and I had the technical explanation so still

Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>

Regards,

quoted

Changes in v3:
- remove qspi flash mapping for the moment
- remove at24 and i2c bindings; this will be introduced when
"Add at24 functionality to read form different EEPROM offsets" patch will
be accepted
- change the title of patch 5 from this series from
"ARM: dts: sama5d27_som1_ek: Add sama5d27 SoM1 EK support" to
"ARM: dts: at91: at91-sama5d27_som1_ek: Add sama5d27 SoM1 EK support" to
match the desired prefix

Changes in v2:
o in at91-sama5d27_som1.dtsi:
- increase bootloader and kernel size in flash map (with bootloader
flash offset the dtb and kernel flash offsets were changed)
- use right pin for ethernet-phy interrupt

o in at91-sama5d27_som1_ek.dts:
- removed memory tag and rely on bootloader to fill the right value
- use pin macros (from arch/arm/boot/dts/sama5d2-pinfunc.h) wherever
posible instead of pin numbers
- remove pinctrl_sensor_power and pinctrl_sensor_reset pin muxing
since they are not of intereset for this board
- use "pb4" label for user button instead of "bp1"

Claudiu Beznea (2):
  ARM: dts: at91: at91-sama5d27_som1: add sama5d27 SoM1 support
  ARM: dts: sama5d27_som1_ek: Add sama5d27 SoM1 EK support

Cristian Birsan (1):
  drivers: soc: atmel: Add basic support for new sama5d2 SiPs

Cyrille Pitchen (1):
  ARM: dts: at91: sama5d2: add QSPI nodes

Songjun Wu (1):
  ARM: dts: at91: sama5d2: add isc node

 arch/arm/boot/dts/Makefile                  |   1 +
 arch/arm/boot/dts/at91-sama5d27_som1.dtsi   | 178 +++++++++
 arch/arm/boot/dts/at91-sama5d27_som1_ek.dts | 551 ++++++++++++++++++++++++++++
 arch/arm/boot/dts/sama5d2.dtsi              |  38 ++
 drivers/soc/atmel/soc.c                     |   8 +
 drivers/soc/atmel/soc.h                     |   4 +
 6 files changed, 780 insertions(+)
 create mode 100644 arch/arm/boot/dts/at91-sama5d27_som1.dtsi
 create mode 100644 arch/arm/boot/dts/at91-sama5d27_som1_ek.dts

-- 
Nicolas Ferre