@@ -4,6 +4,34 @@ Allwinner A10 Display Pipeline
 The Allwinner A10 Display pipeline is composed of several components
 that are going to be documented below:
 
+HDMI Encoder
+------------
+
+The HDMI Encoder supports the HDMI video and audio outputs, and does
+CEC. It is one end of the pipeline.
+
+Required properties:
+  - compatible: value must be one of:
+    * allwinner,sun5i-a10s-hdmi
+  - reg: base address and size of memory-mapped region
+  - interrupts: interrupt associated to this IP
+  - clocks: phandles to the clocks feeding the HDMI encoder
+    * ahb: the HDMI interface clock
+    * mod: the HDMI module clock
+    * pll-0: the first video PLL
+    * pll-1: the second video PLL
+  - clock-names: the clock names mentioned above
+  - dmas: phandles to the DMA channels used by the HDMI encoder
+    * ddc-tx: The channel for DDC transmission
+    * ddc-rx: The channel for DDC reception
+    * audio-tx: The channel used for audio transmission
+  - dma-names: the channel names mentioned above
+
+  - ports: A ports node with endpoint definitions as defined in
+    Documentation/devicetree/bindings/media/video-interfaces.txt. The
+    first port should be the input endpoint. The second should be the
+    output, usually to an HDMI connector.
+
 TV Encoder
 ----------
 

@@ -173,6 +201,57 @@ panel: panel {
 	};
 };
 
+connector {
+	compatible = "hdmi-connector";
+	type = "a";
+
+	port {
+		hdmi_con_in: endpoint {
+			remote-endpoint = <&hdmi_out_con>;
+		};
+	};
+};
+
+hdmi: hdmi at 01c16000 {
+	compatible = "allwinner,sun5i-a10s-hdmi";
+	reg = <0x01c16000 0x1000>;
+	interrupts = <58>;
+	clocks = <&ccu CLK_AHB_HDMI>, <&ccu CLK_HDMI>,
+		 <&ccu CLK_PLL_VIDEO0_2X>,
+		 <&ccu CLK_PLL_VIDEO1_2X>;
+	clock-names = "ahb", "mod", "pll-0", "pll-1";
+	dmas = <&dma SUN4I_DMA_NORMAL 16>,
+	       <&dma SUN4I_DMA_NORMAL 16>,
+	       <&dma SUN4I_DMA_DEDICATED 24>;
+	dma-names = "ddc-tx", "ddc-rx", "audio-tx";
+	status = "disabled";
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port at 0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			hdmi_in_tcon0: endpoint {
+				remote-endpoint = <&tcon0_out_hdmi>;
+			};
+		};
+
+		port at 1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			hdmi_out_con: endpoint {
+				remote-endpoint = <&hdmi_con_in>;
+			};
+		};
+	};
+};
+
 tve0: tv-encoder at 01c0a000 {
 	compatible = "allwinner,sun4i-a10-tv-encoder";
 	reg = <0x01c0a000 0x1000>;