[PATCH v5 5/7] arm: dts: sun8i: split Allwinner H3 .dtsi
From: Chen-Yu Tsai <hidden>
Date: 2017-02-26 03:56:58
Also in:
linux-clk, linux-devicetree, lkml
Hi, On Sun, Feb 26, 2017 at 9:19 AM, Icenowy Zheng [off-list ref] wrote:
quoted hunk ↗ jump to hunk
From: Andre Przywara <andre.przywara@arm.com> The new Allwinner H5 SoC is pin-compatible to the H3 SoC, but with the Cortex-A7 cores replaced by Cortex-A53 cores and the MMC controller updated. So we should really share almost the whole .dtsi. In preparation for that move the peripheral parts of the existing sun8i-h3.dtsi into a new sun8i-h3-h5.dtsi. The actual sun8i-h3.dtsi then includes that and defines the H3 specific parts on top of it. On the way get rid of skeleton.dtsi, as recommended in that very file. Signed-off-by: Andre Przywara <andre.przywara@arm.com> [Icenowy: also split out mmc, as well as pio and ccu's compatible] Signed-off-by: Icenowy Zheng <redacted> --- Changes in v3: - Use label-based syntax to reference nodes in H3 DTSI file. Changes in v2: - Rebase on current linux-next (because of the add of audio codec) arch/arm/boot/dts/sun8i-h3.dtsi | 789 ++++----------------- .../boot/dts/{sun8i-h3.dtsi => sunxi-h3-h5.dtsi} | 87 +-- 2 files changed, 148 insertions(+), 728 deletions(-) rewrite arch/arm/boot/dts/sun8i-h3.dtsi (81%) copy arch/arm/boot/dts/{sun8i-h3.dtsi => sunxi-h3-h5.dtsi} (88%)diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi dissimilarity index 81% index 8a4d7894a11f..4209d974c3f4 100644 --- a/arch/arm/boot/dts/sun8i-h3.dtsi +++ b/arch/arm/boot/dts/sun8i-h3.dtsi@@ -1,648 +1,141 @@ -/* - * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com> - * - * This file is dual-licensed: you can use it either under the terms - * of the GPL or the X11 license, at your option. Note that this dual - * licensing only applies to this file, and not this project as a - * whole. - * - * a) This file is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of the - * License, or (at your option) any later version. - * - * This file is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * Or, alternatively, - * - * b) Permission is hereby granted, free of charge, to any person - * obtaining a copy of this software and associated documentation - * files (the "Software"), to deal in the Software without - * restriction, including without limitation the rights to use, - * copy, modify, merge, publish, distribute, sublicense, and/or - * sell copies of the Software, and to permit persons to whom the - * Software is furnished to do so, subject to the following - * conditions: - * - * The above copyright notice and this permission notice shall be - * included in all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, - * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES - * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND - * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT - * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, - * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING - * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR - * OTHER DEALINGS IN THE SOFTWARE. - */ - -#include "skeleton.dtsi" - -#include <dt-bindings/clock/sunxi-h3-h5-ccu.h> -#include <dt-bindings/interrupt-controller/arm-gic.h> -#include <dt-bindings/pinctrl/sun4i-a10.h> -#include <dt-bindings/reset/sunxi-h3-h5-ccu.h> - -/ { - interrupt-parent = <&gic>; - - cpus { - #address-cells = <1>; - #size-cells = <0>; - - cpu at 0 { - compatible = "arm,cortex-a7"; - device_type = "cpu"; - reg = <0>; - }; - - cpu at 1 { - compatible = "arm,cortex-a7"; - device_type = "cpu"; - reg = <1>; - }; - - cpu at 2 { - compatible = "arm,cortex-a7"; - device_type = "cpu"; - reg = <2>; - }; - - cpu at 3 { - compatible = "arm,cortex-a7"; - device_type = "cpu"; - reg = <3>; - }; - }; - - timer { - compatible = "arm,armv7-timer"; - interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, - <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, - <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, - <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; - }; - - clocks { - #address-cells = <1>; - #size-cells = <1>; - ranges; - - osc24M: osc24M_clk { - #clock-cells = <0>; - compatible = "fixed-clock"; - clock-frequency = <24000000>; - clock-output-names = "osc24M"; - }; - - osc32k: osc32k_clk { - #clock-cells = <0>; - compatible = "fixed-clock"; - clock-frequency = <32768>; - clock-output-names = "osc32k"; - }; - - apb0: apb0_clk { - compatible = "fixed-factor-clock"; - #clock-cells = <0>; - clock-div = <1>; - clock-mult = <1>; - clocks = <&osc24M>; - clock-output-names = "apb0"; - }; - - apb0_gates: clk at 01f01428 { - compatible = "allwinner,sun8i-h3-apb0-gates-clk", - "allwinner,sun4i-a10-gates-clk"; - reg = <0x01f01428 0x4>; - #clock-cells = <1>; - clocks = <&apb0>; - clock-indices = <0>, <1>; - clock-output-names = "apb0_pio", "apb0_ir"; - }; - - ir_clk: ir_clk at 01f01454 { - compatible = "allwinner,sun4i-a10-mod0-clk"; - reg = <0x01f01454 0x4>; - #clock-cells = <0>; - clocks = <&osc32k>, <&osc24M>; - clock-output-names = "ir"; - }; - }; - - soc { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <1>; - ranges; - - dma: dma-controller at 01c02000 { - compatible = "allwinner,sun8i-h3-dma"; - reg = <0x01c02000 0x1000>; - interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&ccu CLK_BUS_DMA>; - resets = <&ccu RST_BUS_DMA>; - #dma-cells = <1>; - }; - - mmc0: mmc at 01c0f000 { - compatible = "allwinner,sun7i-a20-mmc"; - reg = <0x01c0f000 0x1000>; - clocks = <&ccu CLK_BUS_MMC0>, - <&ccu CLK_MMC0>, - <&ccu CLK_MMC0_OUTPUT>, - <&ccu CLK_MMC0_SAMPLE>; - clock-names = "ahb", - "mmc", - "output", - "sample"; - resets = <&ccu RST_BUS_MMC0>; - reset-names = "ahb"; - interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>; - status = "disabled"; - #address-cells = <1>; - #size-cells = <0>; - }; - - mmc1: mmc at 01c10000 { - compatible = "allwinner,sun7i-a20-mmc"; - reg = <0x01c10000 0x1000>; - clocks = <&ccu CLK_BUS_MMC1>, - <&ccu CLK_MMC1>, - <&ccu CLK_MMC1_OUTPUT>, - <&ccu CLK_MMC1_SAMPLE>; - clock-names = "ahb", - "mmc", - "output", - "sample"; - resets = <&ccu RST_BUS_MMC1>; - reset-names = "ahb"; - interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>; - status = "disabled"; - #address-cells = <1>; - #size-cells = <0>; - }; - - mmc2: mmc at 01c11000 { - compatible = "allwinner,sun7i-a20-mmc"; - reg = <0x01c11000 0x1000>; - clocks = <&ccu CLK_BUS_MMC2>, - <&ccu CLK_MMC2>, - <&ccu CLK_MMC2_OUTPUT>, - <&ccu CLK_MMC2_SAMPLE>; - clock-names = "ahb", - "mmc", - "output", - "sample"; - resets = <&ccu RST_BUS_MMC2>; - reset-names = "ahb"; - interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>; - status = "disabled"; - #address-cells = <1>; - #size-cells = <0>; - }; - - usbphy: phy at 01c19400 { - compatible = "allwinner,sun8i-h3-usb-phy"; - reg = <0x01c19400 0x2c>, - <0x01c1a800 0x4>, - <0x01c1b800 0x4>, - <0x01c1c800 0x4>, - <0x01c1d800 0x4>; - reg-names = "phy_ctrl", - "pmu0", - "pmu1", - "pmu2", - "pmu3"; - clocks = <&ccu CLK_USB_PHY0>, - <&ccu CLK_USB_PHY1>, - <&ccu CLK_USB_PHY2>, - <&ccu CLK_USB_PHY3>; - clock-names = "usb0_phy", - "usb1_phy", - "usb2_phy", - "usb3_phy"; - resets = <&ccu RST_USB_PHY0>, - <&ccu RST_USB_PHY1>, - <&ccu RST_USB_PHY2>, - <&ccu RST_USB_PHY3>; - reset-names = "usb0_reset", - "usb1_reset", - "usb2_reset", - "usb3_reset"; - status = "disabled"; - #phy-cells = <1>; - }; - - ehci1: usb at 01c1b000 { - compatible = "allwinner,sun8i-h3-ehci", "generic-ehci"; - reg = <0x01c1b000 0x100>; - interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>; - resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>; - phys = <&usbphy 1>; - phy-names = "usb"; - status = "disabled"; - }; - - ohci1: usb at 01c1b400 { - compatible = "allwinner,sun8i-h3-ohci", "generic-ohci"; - reg = <0x01c1b400 0x100>; - interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>, - <&ccu CLK_USB_OHCI1>; - resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>; - phys = <&usbphy 1>; - phy-names = "usb"; - status = "disabled"; - }; - - ehci2: usb at 01c1c000 { - compatible = "allwinner,sun8i-h3-ehci", "generic-ehci"; - reg = <0x01c1c000 0x100>; - interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>; - resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>; - phys = <&usbphy 2>; - phy-names = "usb"; - status = "disabled"; - }; - - ohci2: usb at 01c1c400 { - compatible = "allwinner,sun8i-h3-ohci", "generic-ohci"; - reg = <0x01c1c400 0x100>; - interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>, - <&ccu CLK_USB_OHCI2>; - resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>; - phys = <&usbphy 2>; - phy-names = "usb"; - status = "disabled"; - }; - - ehci3: usb at 01c1d000 { - compatible = "allwinner,sun8i-h3-ehci", "generic-ehci"; - reg = <0x01c1d000 0x100>; - interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>; - resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>; - phys = <&usbphy 3>; - phy-names = "usb"; - status = "disabled"; - }; - - ohci3: usb at 01c1d400 { - compatible = "allwinner,sun8i-h3-ohci", "generic-ohci"; - reg = <0x01c1d400 0x100>; - interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>, - <&ccu CLK_USB_OHCI3>; - resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>; - phys = <&usbphy 3>; - phy-names = "usb"; - status = "disabled"; - }; - - ccu: clock at 01c20000 { - compatible = "allwinner,sun8i-h3-ccu"; - reg = <0x01c20000 0x400>; - clocks = <&osc24M>, <&osc32k>; - clock-names = "hosc", "losc"; - #clock-cells = <1>; - #reset-cells = <1>; - }; - - pio: pinctrl at 01c20800 { - compatible = "allwinner,sun8i-h3-pinctrl"; - reg = <0x01c20800 0x400>; - interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>; - clock-names = "apb", "hosc", "losc"; - gpio-controller; - #gpio-cells = <3>; - interrupt-controller; - #interrupt-cells = <3>; - - i2c0_pins: i2c0 { - pins = "PA11", "PA12"; - function = "i2c0"; - }; - - i2c1_pins: i2c1 { - pins = "PA18", "PA19"; - function = "i2c1"; - }; - - i2c2_pins: i2c2 { - pins = "PE12", "PE13"; - function = "i2c2"; - }; - - mmc0_pins_a: mmc0 at 0 { - pins = "PF0", "PF1", "PF2", "PF3", - "PF4", "PF5"; - function = "mmc0"; - drive-strength = <30>; - bias-pull-up; - }; - - mmc0_cd_pin: mmc0_cd_pin at 0 { - pins = "PF6"; - function = "gpio_in"; - bias-pull-up; - }; - - mmc1_pins_a: mmc1 at 0 { - pins = "PG0", "PG1", "PG2", "PG3", - "PG4", "PG5"; - function = "mmc1"; - drive-strength = <30>; - bias-pull-up; - }; - - mmc2_8bit_pins: mmc2_8bit { - pins = "PC5", "PC6", "PC8", - "PC9", "PC10", "PC11", - "PC12", "PC13", "PC14", - "PC15", "PC16"; - function = "mmc2"; - drive-strength = <30>; - bias-pull-up; - }; - - spdif_tx_pins_a: spdif at 0 { - pins = "PA17"; - function = "spdif"; - }; - - spi0_pins: spi0 { - pins = "PC0", "PC1", "PC2", "PC3"; - function = "spi0"; - }; - - spi1_pins: spi1 { - pins = "PA15", "PA16", "PA14", "PA13"; - function = "spi1"; - }; - - uart0_pins_a: uart0 at 0 { - pins = "PA4", "PA5"; - function = "uart0"; - }; - - uart1_pins: uart1 { - pins = "PG6", "PG7"; - function = "uart1"; - }; - - uart1_rts_cts_pins: uart1_rts_cts { - pins = "PG8", "PG9"; - function = "uart1"; - }; - - uart2_pins: uart2 { - pins = "PA0", "PA1"; - function = "uart2"; - }; - - uart3_pins: uart3 { - pins = "PA13", "PA14"; - function = "uart3"; - }; - }; - - timer at 01c20c00 { - compatible = "allwinner,sun4i-a10-timer"; - reg = <0x01c20c00 0xa0>; - interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&osc24M>; - }; - - spi0: spi at 01c68000 { - compatible = "allwinner,sun8i-h3-spi"; - reg = <0x01c68000 0x1000>; - interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>; - clock-names = "ahb", "mod"; - dmas = <&dma 23>, <&dma 23>; - dma-names = "rx", "tx"; - pinctrl-names = "default"; - pinctrl-0 = <&spi0_pins>; - resets = <&ccu RST_BUS_SPI0>; - status = "disabled"; - #address-cells = <1>; - #size-cells = <0>; - }; - - spi1: spi at 01c69000 { - compatible = "allwinner,sun8i-h3-spi"; - reg = <0x01c69000 0x1000>; - interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>; - clock-names = "ahb", "mod"; - dmas = <&dma 24>, <&dma 24>; - dma-names = "rx", "tx"; - pinctrl-names = "default"; - pinctrl-0 = <&spi1_pins>; - resets = <&ccu RST_BUS_SPI1>; - status = "disabled"; - #address-cells = <1>; - #size-cells = <0>; - }; - - wdt0: watchdog at 01c20ca0 { - compatible = "allwinner,sun6i-a31-wdt"; - reg = <0x01c20ca0 0x20>; - interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; - }; - - spdif: spdif at 01c21000 { - #sound-dai-cells = <0>; - compatible = "allwinner,sun8i-h3-spdif"; - reg = <0x01c21000 0x400>; - interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&ccu CLK_BUS_SPDIF>, <&ccu CLK_SPDIF>; - resets = <&ccu RST_BUS_SPDIF>; - clock-names = "apb", "spdif"; - dmas = <&dma 2>; - dma-names = "tx"; - status = "disabled"; - }; - - pwm: pwm at 01c21400 { - compatible = "allwinner,sun8i-h3-pwm"; - reg = <0x01c21400 0x8>; - clocks = <&osc24M>; - #pwm-cells = <3>; - status = "disabled"; - }; - - codec: codec at 01c22c00 { - #sound-dai-cells = <0>; - compatible = "allwinner,sun8i-h3-codec"; - reg = <0x01c22c00 0x400>; - interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&ccu CLK_BUS_CODEC>, <&ccu CLK_AC_DIG>; - clock-names = "apb", "codec"; - resets = <&ccu RST_BUS_CODEC>; - dmas = <&dma 15>, <&dma 15>; - dma-names = "rx", "tx"; - allwinner,codec-analog-controls = <&codec_analog>; - status = "disabled"; - }; - - uart0: serial at 01c28000 { - compatible = "snps,dw-apb-uart"; - reg = <0x01c28000 0x400>; - interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>; - reg-shift = <2>; - reg-io-width = <4>; - clocks = <&ccu CLK_BUS_UART0>; - resets = <&ccu RST_BUS_UART0>; - dmas = <&dma 6>, <&dma 6>; - dma-names = "rx", "tx"; - status = "disabled"; - }; - - uart1: serial at 01c28400 { - compatible = "snps,dw-apb-uart"; - reg = <0x01c28400 0x400>; - interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>; - reg-shift = <2>; - reg-io-width = <4>; - clocks = <&ccu CLK_BUS_UART1>; - resets = <&ccu RST_BUS_UART1>; - dmas = <&dma 7>, <&dma 7>; - dma-names = "rx", "tx"; - status = "disabled"; - }; - - uart2: serial at 01c28800 { - compatible = "snps,dw-apb-uart"; - reg = <0x01c28800 0x400>; - interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; - reg-shift = <2>; - reg-io-width = <4>; - clocks = <&ccu CLK_BUS_UART2>; - resets = <&ccu RST_BUS_UART2>; - dmas = <&dma 8>, <&dma 8>; - dma-names = "rx", "tx"; - status = "disabled"; - }; - - uart3: serial at 01c28c00 { - compatible = "snps,dw-apb-uart"; - reg = <0x01c28c00 0x400>; - interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; - reg-shift = <2>; - reg-io-width = <4>; - clocks = <&ccu CLK_BUS_UART3>; - resets = <&ccu RST_BUS_UART3>; - dmas = <&dma 9>, <&dma 9>; - dma-names = "rx", "tx"; - status = "disabled"; - }; - - i2c0: i2c at 01c2ac00 { - compatible = "allwinner,sun6i-a31-i2c"; - reg = <0x01c2ac00 0x400>; - interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&ccu CLK_BUS_I2C0>; - resets = <&ccu RST_BUS_I2C0>; - pinctrl-names = "default"; - pinctrl-0 = <&i2c0_pins>; - status = "disabled"; - #address-cells = <1>; - #size-cells = <0>; - }; - - i2c1: i2c at 01c2b000 { - compatible = "allwinner,sun6i-a31-i2c"; - reg = <0x01c2b000 0x400>; - interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&ccu CLK_BUS_I2C1>; - resets = <&ccu RST_BUS_I2C1>; - pinctrl-names = "default"; - pinctrl-0 = <&i2c1_pins>; - status = "disabled"; - #address-cells = <1>; - #size-cells = <0>; - }; - - i2c2: i2c at 01c2b400 { - compatible = "allwinner,sun6i-a31-i2c"; - reg = <0x01c2b000 0x400>; - interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&ccu CLK_BUS_I2C2>; - resets = <&ccu RST_BUS_I2C2>; - pinctrl-names = "default"; - pinctrl-0 = <&i2c2_pins>; - status = "disabled"; - #address-cells = <1>; - #size-cells = <0>; - }; - - gic: interrupt-controller at 01c81000 { - compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic"; - reg = <0x01c81000 0x1000>, - <0x01c82000 0x2000>, - <0x01c84000 0x2000>, - <0x01c86000 0x2000>; - interrupt-controller; - #interrupt-cells = <3>; - interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; - }; - - rtc: rtc at 01f00000 { - compatible = "allwinner,sun6i-a31-rtc"; - reg = <0x01f00000 0x54>; - interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; - }; - - apb0_reset: reset at 01f014b0 { - reg = <0x01f014b0 0x4>; - compatible = "allwinner,sun6i-a31-clock-reset"; - #reset-cells = <1>; - }; - - codec_analog: codec-analog at 01f015c0 { - compatible = "allwinner,sun8i-h3-codec-analog"; - reg = <0x01f015c0 0x4>; - }; - - ir: ir at 01f02000 { - compatible = "allwinner,sun5i-a13-ir"; - clocks = <&apb0_gates 1>, <&ir_clk>; - clock-names = "apb", "ir"; - resets = <&apb0_reset 1>; - interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; - reg = <0x01f02000 0x40>; - status = "disabled"; - }; - - r_pio: pinctrl at 01f02c00 { - compatible = "allwinner,sun8i-h3-r-pinctrl"; - reg = <0x01f02c00 0x400>; - interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&apb0_gates 0>, <&osc24M>, <&osc32k>; - clock-names = "apb", "hosc", "losc"; - resets = <&apb0_reset 0>; - gpio-controller; - #gpio-cells = <3>; - interrupt-controller; - #interrupt-cells = <3>; - - ir_pins_a: ir at 0 { - pins = "PL11"; - function = "s_cir_rx"; - }; - }; - }; -}; +/* + * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include "sunxi-h3-h5.dtsi" + +/ { + interrupt-parent = <&gic>; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu at 0 { + compatible = "arm,cortex-a7"; + device_type = "cpu"; + reg = <0>; + }; + + cpu at 1 { + compatible = "arm,cortex-a7"; + device_type = "cpu"; + reg = <1>; + }; + + cpu at 2 { + compatible = "arm,cortex-a7"; + device_type = "cpu"; + reg = <2>; + }; + + cpu at 3 { + compatible = "arm,cortex-a7"; + device_type = "cpu"; + reg = <3>; + }; + }; + + timer { + compatible = "arm,armv7-timer"; + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; + }; + + soc { + gic: interrupt-controller at 01c81000 { + compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic"; + reg = <0x01c81000 0x1000>, + <0x01c82000 0x2000>, + <0x01c84000 0x2000>, + <0x01c86000 0x2000>; + interrupt-controller; + #interrupt-cells = <3>; + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; + }; + }; +}; + +&ccu { + compatible = "allwinner,sun8i-h3-ccu"; +}; + +&mmc0 { + compatible = "allwinner,sun7i-a20-mmc"; + clocks = <&ccu CLK_BUS_MMC0>, + <&ccu CLK_MMC0>, + <&ccu CLK_MMC0_OUTPUT>, + <&ccu CLK_MMC0_SAMPLE>; + clock-names = "ahb", + "mmc", + "output", + "sample"; +}; + +&mmc1 { + compatible = "allwinner,sun7i-a20-mmc"; + clocks = <&ccu CLK_BUS_MMC1>, + <&ccu CLK_MMC1>, + <&ccu CLK_MMC1_OUTPUT>, + <&ccu CLK_MMC1_SAMPLE>; + clock-names = "ahb", + "mmc", + "output", + "sample"; +}; + +&mmc2 { + compatible = "allwinner,sun7i-a20-mmc"; + clocks = <&ccu CLK_BUS_MMC2>, + <&ccu CLK_MMC2>, + <&ccu CLK_MMC2_OUTPUT>, + <&ccu CLK_MMC2_SAMPLE>; + clock-names = "ahb", + "mmc", + "output", + "sample"; +}; + +&pio { + compatible = "allwinner,sun8i-h3-pinctrl"; +};diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sunxi-h3-h5.dtsi similarity index 88% copy from arch/arm/boot/dts/sun8i-h3.dtsi copy to arch/arm/boot/dts/sunxi-h3-h5.dtsi index 8a4d7894a11f..966dc4211c4d 100644 --- a/arch/arm/boot/dts/sun8i-h3.dtsi +++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi@@ -40,52 +40,14 @@ * OTHER DEALINGS IN THE SOFTWARE. */ -#include "skeleton.dtsi" - #include <dt-bindings/clock/sunxi-h3-h5-ccu.h> #include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/pinctrl/sun4i-a10.h> #include <dt-bindings/reset/sunxi-h3-h5-ccu.h> / { - interrupt-parent = <&gic>; - - cpus { - #address-cells = <1>; - #size-cells = <0>; - - cpu at 0 { - compatible = "arm,cortex-a7"; - device_type = "cpu"; - reg = <0>; - }; - - cpu at 1 { - compatible = "arm,cortex-a7"; - device_type = "cpu"; - reg = <1>; - }; - - cpu at 2 { - compatible = "arm,cortex-a7"; - device_type = "cpu"; - reg = <2>; - }; - - cpu at 3 { - compatible = "arm,cortex-a7"; - device_type = "cpu"; - reg = <3>; - }; - }; - - timer { - compatible = "arm,armv7-timer"; - interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, - <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, - <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, - <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; - }; + #address-cells = <1>; + #size-cells = <1>; clocks { #address-cells = <1>;@@ -150,16 +112,8 @@ }; mmc0: mmc at 01c0f000 { - compatible = "allwinner,sun7i-a20-mmc"; + /* compatible and clocks are in per SoC .dtsi file */ reg = <0x01c0f000 0x1000>; - clocks = <&ccu CLK_BUS_MMC0>, - <&ccu CLK_MMC0>, - <&ccu CLK_MMC0_OUTPUT>, - <&ccu CLK_MMC0_SAMPLE>; - clock-names = "ahb", - "mmc", - "output", - "sample"; resets = <&ccu RST_BUS_MMC0>; reset-names = "ahb"; interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;@@ -169,16 +123,8 @@ }; mmc1: mmc at 01c10000 { - compatible = "allwinner,sun7i-a20-mmc"; + /* compatible and clocks are in per SoC .dtsi file */ reg = <0x01c10000 0x1000>; - clocks = <&ccu CLK_BUS_MMC1>, - <&ccu CLK_MMC1>, - <&ccu CLK_MMC1_OUTPUT>, - <&ccu CLK_MMC1_SAMPLE>; - clock-names = "ahb", - "mmc", - "output", - "sample"; resets = <&ccu RST_BUS_MMC1>; reset-names = "ahb"; interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;@@ -188,16 +134,8 @@ }; mmc2: mmc at 01c11000 { - compatible = "allwinner,sun7i-a20-mmc"; + /* compatible and clocks are in per SoC .dtsi file */ reg = <0x01c11000 0x1000>; - clocks = <&ccu CLK_BUS_MMC2>, - <&ccu CLK_MMC2>, - <&ccu CLK_MMC2_OUTPUT>, - <&ccu CLK_MMC2_SAMPLE>; - clock-names = "ahb", - "mmc", - "output", - "sample"; resets = <&ccu RST_BUS_MMC2>; reset-names = "ahb"; interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;@@ -308,7 +246,7 @@ }; ccu: clock at 01c20000 { - compatible = "allwinner,sun8i-h3-ccu"; + /* compatible is in per SoC .dtsi file */ reg = <0x01c20000 0x400>; clocks = <&osc24M>, <&osc32k>; clock-names = "hosc", "losc";@@ -317,7 +255,7 @@ }; pio: pinctrl at 01c20800 { - compatible = "allwinner,sun8i-h3-pinctrl"; + /* compatible is in per SoC .dtsi file */ reg = <0x01c20800 0x400>; interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;@@ -588,17 +526,6 @@ #size-cells = <0>; }; - gic: interrupt-controller at 01c81000 { - compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic"; - reg = <0x01c81000 0x1000>, - <0x01c82000 0x2000>, - <0x01c84000 0x2000>, - <0x01c86000 0x2000>; - interrupt-controller; - #interrupt-cells = <3>; - interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
The gic bits seem to be the same for both SoCs, aside from the different compatible string. Marc had sent a series to change them all to arm,gic-400, which is the proper name for it, but it wasn't merged. I'm assuming the compatibles are equal? If so then it can also be shared. The rest looks ok. ChenYu
- };
-
rtc: rtc at 01f00000 {
compatible = "allwinner,sun6i-a31-rtc";
reg = <0x01f00000 0x54>;
--
2.11.1