@@ -679,6 +611,123 @@ static int serial_ir_resume(struct platform_device *dev)
return 0;
}
+static int serial_ir_probe(struct platform_device *dev)
+{
+ struct rc_dev *rcdev;
+ int i, nlow, nhigh, result;
+
+ rcdev = devm_rc_allocate_device(&dev->dev, RC_DRIVER_IR_RAW);
+ if (!rcdev)
+ return -ENOMEM;
+
+ if (hardware[type].send_pulse && hardware[type].send_space)
+ rcdev->tx_ir = serial_ir_tx;
+ if (hardware[type].set_send_carrier)
+ rcdev->s_tx_carrier = serial_ir_tx_carrier;
+ if (hardware[type].set_duty_cycle)
+ rcdev->s_tx_duty_cycle = serial_ir_tx_duty_cycle;
+
+ switch (type) {
+ case IR_HOMEBREW:
+ rcdev->input_name = "Serial IR type home-brew";
+ break;
+ case IR_IRDEO:
+ rcdev->input_name = "Serial IR type IRdeo";
+ break;
+ case IR_IRDEO_REMOTE:
+ rcdev->input_name = "Serial IR type IRdeo remote";
+ break;
+ case IR_ANIMAX:
+ rcdev->input_name = "Serial IR type AnimaX";
+ break;
+ case IR_IGOR:
+ rcdev->input_name = "Serial IR type IgorPlug";
+ break;
+ }
+
+ rcdev->input_phys = KBUILD_MODNAME "/input0";
+ rcdev->input_id.bustype = BUS_HOST;
+ rcdev->input_id.vendor = 0x0001;
+ rcdev->input_id.product = 0x0001;
+ rcdev->input_id.version = 0x0100;
+ rcdev->open = serial_ir_open;
+ rcdev->close = serial_ir_close;
+ rcdev->dev.parent = &serial_ir.pdev->dev;
+ rcdev->allowed_protocols = RC_BIT_ALL_IR_DECODER;
+ rcdev->driver_name = KBUILD_MODNAME;
+ rcdev->map_name = RC_MAP_RC6_MCE;
+ rcdev->min_timeout = 1;
+ rcdev->timeout = IR_DEFAULT_TIMEOUT;
+ rcdev->max_timeout = 10 * IR_DEFAULT_TIMEOUT;
+ rcdev->rx_resolution = 250000;
+
+ serial_ir.rcdev = rcdev;
+
+ setup_timer(&serial_ir.timeout_timer, serial_ir_timeout,
+ (unsigned long)&serial_ir);
+
+ result = devm_request_irq(&dev->dev, irq, serial_ir_irq_handler,
+ share_irq ? IRQF_SHARED : 0,
+ KBUILD_MODNAME, &hardware);
+ if (result < 0) {
+ if (result == -EBUSY)
+ dev_err(&dev->dev, "IRQ %d busy\n", irq);
+ else if (result == -EINVAL)
+ dev_err(&dev->dev, "Bad irq number or handler\n");
+ return result;
+ }
+
+ /* Reserve io region. */
+ if ((iommap &&
+ (devm_request_mem_region(&dev->dev, iommap, 8 << ioshift,
+ KBUILD_MODNAME) == NULL)) ||
+ (!iommap && (devm_request_region(&dev->dev, io, 8,
+ KBUILD_MODNAME) == NULL))) {
+ dev_err(&dev->dev, "port %04x already in use\n", io);
+ dev_warn(&dev->dev, "use 'setserial /dev/ttySX uart none'\n");
+ dev_warn(&dev->dev,
+ "or compile the serial port driver as module and\n");
+ dev_warn(&dev->dev, "make sure this module is loaded first\n");
+ return -EBUSY;
+ }
+
+ result = hardware_init_port();
+ if (result < 0)
+ return result;
+
+ /* Initialize pulse/space widths */
+ init_timing_params(50, 38000);
+
+ /* If pin is high, then this must be an active low receiver. */
+ if (sense == -1) {
+ /* wait 1/2 sec for the power supply */
+ msleep(500);
+
+ /*
+ * probe 9 times every 0.04s, collect "votes" for
+ * active high/low
+ */
+ nlow = 0;
+ nhigh = 0;
+ for (i = 0; i < 9; i++) {
+ if (sinp(UART_MSR) & hardware[type].signal_pin)
+ nlow++;
+ else
+ nhigh++;
+ msleep(40);
+ }
+ sense = nlow >= nhigh ? 1 : 0;
+ dev_info(&dev->dev, "auto-detected active %s receiver\n",
+ sense ? "low" : "high");
+ } else
+ dev_info(&dev->dev, "Manually using active %s receiver\n",
+ sense ? "low" : "high");
+
+ dev_dbg(&dev->dev, "Interrupt %d, port %04x obtained\n", irq, io);
+
+ return devm_rc_register_device(&dev->dev, rcdev);
+}
+
static struct platform_driver serial_ir_driver = {
.probe = serial_ir_probe,
.suspend = serial_ir_suspend,@@ -723,7 +772,6 @@ static void serial_ir_exit(void)
static int __init serial_ir_init_module(void)
{
- struct rc_dev *rcdev;
int result;
switch (type) {@@ -754,63 +802,9 @@ static int __init serial_ir_init_module(void)
sense = !!sense;
result = serial_ir_init();
- if (result)
- return result;
-
- rcdev = devm_rc_allocate_device(&serial_ir.pdev->dev, RC_DRIVER_IR_RAW);
- if (!rcdev) {
- result = -ENOMEM;
- goto serial_cleanup;
- }
-
- if (hardware[type].send_pulse && hardware[type].send_space)
- rcdev->tx_ir = serial_ir_tx;
- if (hardware[type].set_send_carrier)
- rcdev->s_tx_carrier = serial_ir_tx_carrier;
- if (hardware[type].set_duty_cycle)
- rcdev->s_tx_duty_cycle = serial_ir_tx_duty_cycle;
-
- switch (type) {
- case IR_HOMEBREW:
- rcdev->input_name = "Serial IR type home-brew";
- break;
- case IR_IRDEO:
- rcdev->input_name = "Serial IR type IRdeo";
- break;
- case IR_IRDEO_REMOTE:
- rcdev->input_name = "Serial IR type IRdeo remote";
- break;
- case IR_ANIMAX:
- rcdev->input_name = "Serial IR type AnimaX";
- break;
- case IR_IGOR:
- rcdev->input_name = "Serial IR type IgorPlug";
- break;
- }
-
- rcdev->input_phys = KBUILD_MODNAME "/input0";
- rcdev->input_id.bustype = BUS_HOST;
- rcdev->input_id.vendor = 0x0001;
- rcdev->input_id.product = 0x0001;
- rcdev->input_id.version = 0x0100;
- rcdev->open = serial_ir_open;
- rcdev->close = serial_ir_close;
- rcdev->dev.parent = &serial_ir.pdev->dev;
- rcdev->allowed_protocols = RC_BIT_ALL_IR_DECODER;
- rcdev->driver_name = KBUILD_MODNAME;
- rcdev->map_name = RC_MAP_RC6_MCE;
- rcdev->min_timeout = 1;
- rcdev->timeout = IR_DEFAULT_TIMEOUT;
- rcdev->max_timeout = 10 * IR_DEFAULT_TIMEOUT;
- rcdev->rx_resolution = 250000;
-
- serial_ir.rcdev = rcdev;
-
- result = rc_register_device(rcdev);
-
if (!result)
return 0;
-serial_cleanup:
+
serial_ir_exit();
return result;
}@@ -818,7 +812,6 @@ static int __init serial_ir_init_module(void)
static void __exit serial_ir_exit_module(void)
{
del_timer_sync(&serial_ir.timeout_timer);
- rc_unregister_device(serial_ir.rcdev);
serial_ir_exit();
}