Thread (33 messages) 33 messages, 3 authors, 2017-02-21
STALE3382d
Revisions (6)
  1. v1 current
  2. v2 [diff vs current]
  3. v3 [diff vs current]
  4. v4 [diff vs current]
  5. v5 [diff vs current]
  6. v6 [diff vs current]

[PATCH 16/21] ARM64: dts: sun50i-a64: add dwmac-sun8i Ethernet driver

From: clabbe.montjoie@gmail.com (Corentin Labbe)
Date: 2017-02-16 12:52:35
Also in: linux-devicetree, lkml, netdev
Subsystem: arm/allwinner sunxi soc support, the rest · Maintainers: Chen-Yu Tsai, Jernej Skrabec, Samuel Holland, Linus Torvalds

The dwmac-sun8i is an Ethernet MAC that supports 10/100/1000 Mbit
connections. It is very similar to the device found in the Allwinner
H3, but lacks the internal 100 Mbit PHY and its associated control
bits.
This adds the necessary bits to the Allwinner A64 SoC .dtsi, but keeps
it disabled at this level.

Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
---
 arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 37 +++++++++++++++++++++++++++
 1 file changed, 37 insertions(+)
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
index 3b09af2..57d69e5 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
@@ -277,6 +277,23 @@
 				bias-pull-up;
 			};
 
+			rmii_pins: rmii_pins {
+				pins = "PD10", "PD11", "PD13", "PD14",
+						"PD17", "PD18", "PD19", "PD20",
+						"PD22", "PD23";
+				function = "emac";
+				drive-strength = <40>;
+			};
+
+			rgmii_pins: rgmii_pins {
+				pins = "PD8", "PD9", "PD10", "PD11",
+						"PD12", "PD13", "PD15",
+						"PD16", "PD17", "PD18", "PD19",
+						"PD20", "PD21", "PD22", "PD23";
+				function = "emac";
+				drive-strength = <40>;
+			};
+
 			uart0_pins_a: uart0 at 0 {
 				pins = "PB8", "PB9";
 				function = "uart0";
@@ -381,6 +398,26 @@
 			#size-cells = <0>;
 		};
 
+		emac: ethernet at 1c30000 {
+			compatible = "allwinner,sun50i-a64-emac";
+			syscon = <&syscon>;
+			reg = <0x01c30000 0x100>;
+			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+			resets = <&ccu RST_BUS_EMAC>;
+			reset-names = "stmmaceth";
+			clocks = <&ccu CLK_BUS_EMAC>;
+			clock-names = "stmmaceth";
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			mdio: mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
 		gic: interrupt-controller at 1c81000 {
 			compatible = "arm,gic-400";
 			reg = <0x01c81000 0x1000>,
-- 
2.10.2
Keyboard shortcuts
hback out one level
jnext message in thread
kprevious message in thread
ldrill in
Escclose help / fold thread tree
?toggle this help