Hi,

On 01/17/2017 10:38 PM, Romain Perier wrote:

Hi,

In my case I can reproduce the issue on the rock2 and the firefly-rk3288. A workaround is to

comment the line ".pm = <&pm_ops_foo>" .

Sorry for late. I'm checking runtime PM for this. 
After that, i will decide whether revert or not.

Best Regards,
Jaehoon Chung

Thanks,
Romain


Le 17/01/2017 ? 14:28, Romain Perier a ?crit :

quoted

Hello,

This commit also breaks reboot and poweroff (the pmic no longer turn the power supply off), see below:

# poweroff
# Stopping network: ifdown: interface lo not configured
OK
Saving random seed... done.
Stopping logging: OK
umount: devtmpfs busy - remounted read-only
The system is going down NOW!
Sent SIGTERM to all processes
Sent SIGKILL to all processes
Requesting system poweroff
[  243.673159] INFO: task init:168 blocked for more than 120 seconds.
[  243.701298]       Not tainted 4.10.0-rc4-13066-gc10b6c6 #108
[  243.728802] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[  243.758948] init            D    0   168      1 0x00000000
[  243.786412] [<c0888740>] (__schedule) from [<c0888b10>] (schedule+0x44/0x9c)
[  243.815411] [<c0888b10>] (schedule) from [<c088c218>] (schedule_timeout+0x1d8/0x220)
[  243.845267] [<c088c218>] (schedule_timeout) from [<c0889528>] (wait_for_common+0xa4/0x168)
[  243.876105] [<c0889528>] (wait_for_common) from [<c06da03c>] (mmc_wait_for_req_done+0x8c/0x110)
[  243.907150] [<c06da03c>] (mmc_wait_for_req_done) from [<c06da204>] (mmc_wait_for_cmd+0x58/0x78)
[  243.937855] [<c06da204>] (mmc_wait_for_cmd) from [<c06e14ec>] (__mmc_switch+0xbc/0x34c)
[  243.967791] [<c06e14ec>] (__mmc_switch) from [<c06e17a4>] (mmc_switch+0x28/0x30)
[  243.997029] [<c06e17a4>] (mmc_switch) from [<c06db144>] (mmc_flush_cache+0x54/0x80)
[  244.026955] [<c06db144>] (mmc_flush_cache) from [<c06e0084>] (_mmc_suspend+0x40/0x268)
[  244.057529] [<c06e0084>] (_mmc_suspend) from [<c06dcf3c>] (mmc_bus_shutdown+0x40/0x64)
[  244.088412] [<c06dcf3c>] (mmc_bus_shutdown) from [<c04db050>] (device_shutdown+0x144/0x1d8)
[  244.120015] [<c04db050>] (device_shutdown) from [<c01503b8>] (kernel_power_off+0x34/0x70)
[  244.151235] [<c01503b8>] (kernel_power_off) from [<c0150598>] (SyS_reboot+0x15c/0x1d0)
[  244.182037] [<c0150598>] (SyS_reboot) from [<c01076c0>] (ret_fast_syscall+0x0/0x3c)
[  366.553025] INFO: task init:168 blocked for more than 120 seconds.
[  366.583187]       Not tainted 4.10.0-rc4-13066-gc10b6c6 #108
[  366.613053] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.



Reverting this commit solves the issue.

Regards,
Romain


2016-12-30 3:50 GMT+01:00 Jaehoon Chung <jh80.chung at samsung.com <mailto:jh80.chung@samsung.com>>:

    On 12/30/2016 11:44 AM, Randy Li wrote:
    >
    >
    > On 12/30/2016 10:35 AM, Jaehoon Chung wrote:
    >> On 12/30/2016 12:07 AM, ayaka wrote:
    >>>
    >>>
    >>> On 12/29/2016 10:04 PM, Jaehoon Chung wrote:
    >>>> Hi,
    >>>>
    >>>> On 12/29/2016 09:55 PM, ayaka wrote:
    >>>>> [    5.849733] rk_gmac-dwmac ff290000.ethernet (unnamed
    net_device) (uninitialized): Enable RX Mitigation via HW Watchdog
    Timer
    >>>>> [    5.944512] mmc_host mmc1: Bus speed (slot 0) =
    50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
    >>>>> [    5.958249] mmc1: new ultra high speed DDR50 SDIO card at
    address 0001
    >>>>> [    6.294548] dwmmc_rockchip ff0f0000.dwmmc: Successfully
    tuned phase to 177
    >>>>> [    6.301591] mmc2: new HS200 MMC card at address 0001
    >>>>> [    6.306758] mmc_host mmc0: Bus speed (slot 0) = 300000Hz
    (slot req 300000Hz, actual 300000HZ div = 0)
    >>>>> [    6.316830] mmcblk2: mmc2:0001 AGND3R 14.6 GiB
    >>>>> [    6.321881] mmcblk2boot0: mmc2:0001 AGND3R partition 1
    4.00 MiB
    >>>>> [    6.328331] mmcblk2boot1: mmc2:0001 AGND3R partition 2
    4.00 MiB
    >>>>> [    6.334792] mmcblk2rpmb: mmc2:0001 AGND3R partition 3
    4.00 MiB
    >>>>> [    6.344295]  mmcblk2: p1 p2 p3 p4 p5 p6 p7
    >>>>> [    6.469892] mmc_host mmc0: Bus speed (slot 0) = 200000Hz
    (slot req 200000Hz, actual 200000HZ div = 0)
    >>>>> [    6.621888] mmc_host mmc0: Bus speed (slot 0) = 187500Hz
    (slot req 100000Hz, actual 93750HZ div = 1)
    >>>>> [    6.917883] libphy: stmmac: probed
    >>>>> [    6.921319] rk_gmac-dwmac ff290000.ethernet eth0: PHY ID
    001cc915 at 0 IRQ POLL (stmmac-0:00) active
    >>>>> [    6.930476] rk_gmac-dwmac ff290000.ethernet eth0: PHY ID
    001cc915 at 2 IRQ POLL (stmmac-0:02)
    >>>>> [    6.939757] input: gpio-keys as
    /devices/platform/gpio-keys/input/input0
    >>>>> [    6.946937] rtc-hym8563 0-0051: no valid clock/calendar
    values available
    >>>>> [    6.953694] rtc-hym8563 0-0051: hctosys: unable to read
    the hardware clock
    >>>>> [    6.961262] vcc_sd: disabling
    >>>>> [    6.964275] dovdd_1v8: disabling
    >>>>> [    6.967527] dvdd_1v2: disabling
    >>>>> [    6.971006] vdd10_lcd: disabling
    >>>>> [    6.974701] vcc18_lcd: disabling
    >>>>> [    6.978467] ttyS2 - failed to request DMA
    >>>>> [    7.101883] mmc_host mmc0: Bus speed (slot 0) = 400000Hz
    (slot req 400000Hz, actual 400000HZ div = 0)
    >>>>> [    7.253874] mmc_host mmc0: Bus speed (slot 0) = 300000Hz
    (slot req 300000Hz, actual 300000HZ div = 0)
    >>>>> [    7.405883] mmc_host mmc0: Bus speed (slot 0) = 200000Hz
    (slot req 200000Hz, actual 200000HZ div = 0)
    >>>>> [    7.557885] mmc_host mmc0: Bus speed (slot 0) = 187500Hz
    (slot req 100000Hz, actual 93750HZ div = 1)
    >>>>> [    8.037872] mmc_host mmc0: Bus speed (slot 0) = 400000Hz
    (slot req 400000Hz, actual 400000HZ div = 0)
    >>>>> [    8.189877] mmc_host mmc0: Bus speed (slot 0) = 300000Hz
    (slot req 300000Hz, actual 300000HZ div = 0)
    >>>>> [    8.341881] mmc_host mmc0: Bus speed (slot 0) = 200000Hz
    (slot req 200000Hz, actual 200000HZ div = 0)
    >>>>> [    8.493884] mmc_host mmc0: Bus speed (slot 0) = 187500Hz
    (slot req 100000Hz, actual 93750HZ div = 1)
    >>>>> [    8.973871] mmc_host mmc0: Bus speed (slot 0) = 400000Hz
    (slot req 400000Hz, actual 400000HZ div = 0)
    >>>>> [    9.125876] mmc_host mmc0: Bus speed (slot 0) = 300000Hz
    (slot req 300000Hz, actual 300000HZ div = 0)
    >>>>> [    9.277884] mmc_host mmc0: Bus speed (slot 0) = 200000Hz
    (slot req 200000Hz, actual 200000HZ div = 0)
    >>>>> [    9.429882] mmc_host mmc0: Bus speed (slot 0) = 187500Hz
    (slot req 100000Hz, actual 93750HZ div = 1)
    >>>>>
    >>>>> looping here
    >>>>>
    >>>>> If I revert that patch, there are still lots of Bus speed
    messages, but finally would enter into system.
    >>>>>
    >>>> Plz..Don't put the comment on the top.
    >>>>
    >>>> Which kernel did you use?
    >>> Add linux-next specific files for 20161224
    >>
    >> mmc0 is what card? Is it polling for detecting card?
    >> (It seems the SD-card..right?)
    > Yes, but the Firefly release won't show that, just stop at
    "ttyS2 - failed to request DMA". I check both the firefly reload
    and firefly release, they both have a cd line for them, so it
    won't be poll mode.

    I don't have Rockchip board, so I hope that Shawn will check it.
    But i will check the displayed the log message.

    Best Regards,
    Jaehoon Chung

    >> Those logs should be polled for detecting mmc0 card..Hmm..I
    sent the patch for disabling log message when polling.
    >> If this log is displayed, then my patch might be some wrong.. :(
    >>
    >> Best Regards,
    >> Jaehoon Chung
    >>
    >>>>
    >>>>>>>>
    >>>>>>>>
    >>>>>>>>
    >>>>>>>
    >>
    >> [snip]
    >>
    >>>
    >>>
    >>>
    >>>
    >>
    >>
    >


    _______________________________________________
    Linux-rockchip mailing list
    Linux-rockchip at lists.infradead.org
    <mailto:Linux-rockchip@lists.infradead.org>
    http://lists.infradead.org/mailman/listinfo/linux-rockchip
    <http://lists.infradead.org/mailman/listinfo/linux-rockchip>