Re: [PATCH] arm64: Add DTS support for FSL's LS1012A SoC

4 messages, 2 authors, 2016-11-15 · open the first message on its own page

Re: [PATCH] arm64: Add DTS support for FSL's LS1012A SoC

From: Shawn Guo <hidden>
Date: 2016-11-14 07:13:10 

On Wed, Nov 09, 2016 at 11:41:58PM +0530, Harninder Rai wrote:
Add the device tree support for FSL LS1012A SoC.
Can we have a brief introduction of this SoC in commit log?
quoted hunk
    Following levels of DTSI/DTS files have been created for the LS1012A
    SoC family:

            - fsl-ls1012a.dtsi:
                    DTS-Include file for FSL LS1012A SoC.

            - fsl-ls1012a-frdm.dts:
                    DTS file for FSL LS1012A FRDM board.

            - fsl-ls1012a-qds.dts:
                    DTS file for FSL LS1012A QDS board.

            - fsl-ls1012a-rdb.dts:
                    DTS file for FSL LS1012A RDB board.

Signed-off-by: Harninder Rai <redacted>
Signed-off-by: Bhaskar Upadhaya <redacted>
---
 arch/arm64/boot/dts/freescale/Makefile             |   3 +
 arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dts | 115 ++++++++++
 arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts  | 128 +++++++++++
 arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts  |  59 +++++
 arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi     | 248 +++++++++++++++++++++
 5 files changed, 553 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dts
 create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts
 create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts
 create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 6602718..39db645 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -1,3 +1,6 @@
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-frdm.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-qds.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-rdb.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1043a-qds.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1043a-rdb.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1046a-qds.dtb
It seems that the patch is not generated against mainline kernel.  We do
not have fsl-ls1046a-qds.dtb target in mainline kernel.
quoted hunk
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dts b/arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dts
new file mode 100644
index 0000000..1f2da79
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dts
@@ -0,0 +1,115 @@
+/*
+ * Device Tree file for Freescale LS1012A Freedom Board.
+ *
+ * Copyright 2016, Freescale Semiconductor
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPLv2 or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+
+#include "fsl-ls1012a.dtsi"
+
+/ {
+	model = "LS1012A Freedom Board";
+	compatible = "fsl,ls1012a-frdm", "fsl,ls1012a";
+
+	sys_mclk: clock-mclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
+	};
+
+	reg_1p8v: regulator at 0 {
Drop the unit-address from node name, and name it like regulator-1p8v.

+		compatible = "regulator-fixed";
+		regulator-name = "1P8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,widgets =
+			"Microphone", "Microphone Jack",
+			"Headphone", "Headphone Jack",
+			"Speaker", "Speaker Ext",
+			"Line", "Line In Jack";
+		simple-audio-card,routing =
+			"MIC_IN", "Microphone Jack",
+			"Microphone Jack", "Mic Bias",
+			"LINE_IN", "Line In Jack",
+			"Headphone Jack", "HP_OUT",
+			"Speaker Ext", "LINE_OUT";
+
+		simple-audio-card,cpu {
+			sound-dai = <&sai2>;
+			frame-master;
+			bitclock-master;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&codec>;
+			frame-master;
+			bitclock-master;
+			system-clock-frequency = <25000000>;
+		};
+	};
+};
+
+&i2c0 {
+	status = "okay";
+
+	codec: sgtl5000 at a {
+		#sound-dai-cells = <0>;
+		compatible = "fsl,sgtl5000";
+		reg = <0xa>;
+		VDDA-supply = <&reg_1p8v>;
+		VDDIO-supply = <&reg_1p8v>;
+		clocks = <&sys_mclk>;
+	};
+};
+
+&duart0 {
Please sort labeled nodes alphabetically.

+	status = "okay";
+};
+
+&sai2 {
+	status = "okay";
+};
<snip>
quoted hunk
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
new file mode 100644
index 0000000..0bf5b64
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
@@ -0,0 +1,248 @@
+/*
+ * Device Tree Include file for Freescale Layerscape-1012A family SoC.
+ *
+ * Copyright 2016, Freescale Semiconductor
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPLv2 or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "fsl,ls1012a";
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu at 0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x0>;
+			clocks = <&clockgen 1 0>;
+			#cooling-cells = <2>;
+		};
+	};
+
+	sysclk: sysclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <100000000>;
+		clock-output-names = "sysclk";
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+			     /* Physical Secure PPI */
+		interrupts = <1 13 IRQ_TYPE_LEVEL_LOW>,
+			     /* Physical Non-Secure PPI */
+			     <1 14 IRQ_TYPE_LEVEL_LOW>,
+			     /* Virtual PPI */
+			     <1 11 IRQ_TYPE_LEVEL_LOW>,
+			     /* Hypervisor PPI */
+			     <1 10 IRQ_TYPE_LEVEL_LOW>;
The following form should be easier for read.

		interrupts = <1 13 IRQ_TYPE_LEVEL_LOW>, /* Physical Secure PPI */
			     <1 14 IRQ_TYPE_LEVEL_LOW>, /* Physical Non-Secure PPI */
			     <1 11 IRQ_TYPE_LEVEL_LOW>, /* Virtual PPI */
			     <1 10 IRQ_TYPE_LEVEL_LOW>; /* Hypervisor PPI */


+	};
+
+	pmu {
+		compatible = "arm,armv8-pmuv3";
+		interrupts = <0 106 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	gic: interrupt-controller at 1400000 {
+		compatible = "arm,gic-400";
+		#interrupt-cells = <3>;
+		interrupt-controller;
+		reg = <0x0 0x1401000 0 0x1000>, /* GICD */
+		      <0x0 0x1402000 0 0x2000>, /* GICC */
+		      <0x0 0x1404000 0 0x2000>, /* GICH */
+		      <0x0 0x1406000 0 0x2000>; /* GICV */
+		interrupts = <1 9 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	reboot {
+		compatible = "syscon-reboot";
+		regmap = <&dcfg>;
+		offset = <0xb0>;
+		mask = <0x02>;
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		clockgen: clocking at 1ee1000 {
+			compatible = "fsl,ls1012a-clockgen";
+			reg = <0x0 0x1ee1000 0x0 0x1000>;
+			#clock-cells = <2>;
+			clocks = <&sysclk>;
+		};
+
+		scfg: scfg at 1570000 {
+			compatible = "fsl,ls1012a-scfg", "syscon";
+			reg = <0x0 0x1570000 0x0 0x10000>;
+			big-endian;
+		};
Please sort these nodes with unit-address in order of the address.

Shawn

+
+		dcfg: dcfg at 1ee0000 {
+			compatible = "fsl,ls1012a-dcfg",
+				     "syscon";
+			reg = <0x0 0x1ee0000 0x0 0x10000>;
+			big-endian;
+		};
+
+		i2c0: i2c at 2180000 {
+			compatible = "fsl,vf610-i2c";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0x2180000 0x0 0x10000>;
+			interrupts = <0 56 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&clockgen 4 0>;
+			status = "disabled";
+		};
+
+		i2c1: i2c at 2190000 {
+			compatible = "fsl,vf610-i2c";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0x2190000 0x0 0x10000>;
+			interrupts = <0 57 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&clockgen 4 0>;
+			status = "disabled";
+		};
+
+		duart0: serial at 21c0500 {
+			compatible = "fsl,ns16550", "ns16550a";
+			reg = <0x00 0x21c0500 0x0 0x100>;
+			interrupts = <0 54 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen 4 0>;
+		};
+
+		duart1: serial at 21c0600 {
+			compatible = "fsl,ns16550", "ns16550a";
+			reg = <0x00 0x21c0600 0x0 0x100>;
+			interrupts = <0 54 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen 4 0>;
+		};
+
+		gpio0: gpio at 2300000 {
+			compatible = "fsl,qoriq-gpio";
+			reg = <0x0 0x2300000 0x0 0x10000>;
+			interrupts = <0 66 IRQ_TYPE_LEVEL_LOW>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio1: gpio at 2310000 {
+			compatible = "fsl,qoriq-gpio";
+			reg = <0x0 0x2310000 0x0 0x10000>;
+			interrupts = <0 67 IRQ_TYPE_LEVEL_LOW>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		wdog0: wdog at 2ad0000 {
+			compatible = "fsl,ls1012a-wdt",
+				     "fsl,imx21-wdt";
+			reg = <0x0 0x2ad0000 0x0 0x10000>;
+			interrupts = <0 83 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&clockgen 4 0>;
+			big-endian;
+		};
+
+		sai1: sai at 2b50000 {
+			#sound-dai-cells = <0>;
+			compatible = "fsl,vf610-sai";
+			reg = <0x0 0x2b50000 0x0 0x10000>;
+			interrupts = <0 148 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&clockgen 4 3>, <&clockgen 4 3>,
+				 <&clockgen 4 3>, <&clockgen 4 3>;
+			clock-names = "bus", "mclk1", "mclk2", "mclk3";
+			dma-names = "tx", "rx";
+			dmas = <&edma0 1 47>,
+			       <&edma0 1 46>;
+			status = "disabled";
+		};
+
+		sai2: sai at 2b60000 {
+			#sound-dai-cells = <0>;
+			compatible = "fsl,vf610-sai";
+			reg = <0x0 0x2b60000 0x0 0x10000>;
+			interrupts = <0 149 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&clockgen 4 3>, <&clockgen 4 3>,
+				 <&clockgen 4 3>, <&clockgen 4 3>;
+			clock-names = "bus", "mclk1", "mclk2", "mclk3";
+			dma-names = "tx", "rx";
+			dmas = <&edma0 1 45>,
+			       <&edma0 1 44>;
+			status = "disabled";
+		};
+
+		edma0: edma at 2c00000 {
+			#dma-cells = <2>;
+			compatible = "fsl,vf610-edma";
+			reg = <0x0 0x2c00000 0x0 0x10000>,
+			      <0x0 0x2c10000 0x0 0x10000>,
+			      <0x0 0x2c20000 0x0 0x10000>;
+			interrupts = <0 103 IRQ_TYPE_LEVEL_LOW>,
+				     <0 103 IRQ_TYPE_LEVEL_LOW>;
+			interrupt-names = "edma-tx", "edma-err";
+			dma-channels = <32>;
+			big-endian;
+			clock-names = "dmamux0", "dmamux1";
+			clocks = <&clockgen 4 3>,
+				 <&clockgen 4 3>;
+		};
+
+		sata: sata at 3200000 {
+			compatible = "fsl,ls1012a-ahci";
+			reg = <0x0 0x3200000 0x0 0x10000>;
+			interrupts = <0 69 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&clockgen 4 0>;
+		};
+	};
+};
-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel at lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH] arm64: Add DTS support for FSL's LS1012A SoC

From: Shawn Guo <hidden>
Date: 2016-11-15 01:18:17 

On Mon, Nov 14, 2016 at 03:13:10PM +0800, Shawn Guo wrote:
quoted
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 6602718..39db645 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -1,3 +1,6 @@
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-frdm.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-qds.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-rdb.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1043a-qds.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1043a-rdb.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1046a-qds.dtb
It seems that the patch is not generated against mainline kernel.  We do
not have fsl-ls1046a-qds.dtb target in mainline kernel.
Sorry, forgot that we just added it in this development cycle.

Shawn

RE: [PATCH] arm64: Add DTS support for FSL's LS1012A SoC

From: Harninder Rai <hidden>
Date: 2016-11-15 06:45:23

quoted
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1043a-qds.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1043a-rdb.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1046a-qds.dtb
It seems that the patch is not generated against mainline kernel.  We do not
have fsl-ls1046a-qds.dtb target in mainline kernel.
You already clarified in the following mail :)
quoted
+
+	reg_1p8v: regulator at 0 {
Drop the unit-address from node name, and name it like regulator-1p8v.
Ok. Will take care in V2
quoted
+
+&duart0 {
Please sort labeled nodes alphabetically.
Ok Sure
quoted
+	status = "okay";
+};
+
+&sai2 {
+	status = "okay";
+};
<snip>

quoted
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
b/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
new file mode 100644
index 0000000..0bf5b64
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
@@ -0,0 +1,248 @@
+/*
+ * Device Tree Include file for Freescale Layerscape-1012A family SoC.
+ *
+ * Copyright 2016, Freescale Semiconductor
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPLv2 or the X11 license, at your option. Note that this
+dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY
KIND,
quoted
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
WARRANTIES
quoted
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR
COPYRIGHT
quoted
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
ARISING
quoted
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE
OR
quoted
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "fsl,ls1012a";
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu at 0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x0>;
+			clocks = <&clockgen 1 0>;
+			#cooling-cells = <2>;
+		};
+	};
+
+	sysclk: sysclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <100000000>;
+		clock-output-names = "sysclk";
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+			     /* Physical Secure PPI */
+		interrupts = <1 13 IRQ_TYPE_LEVEL_LOW>,
+			     /* Physical Non-Secure PPI */
+			     <1 14 IRQ_TYPE_LEVEL_LOW>,
+			     /* Virtual PPI */
+			     <1 11 IRQ_TYPE_LEVEL_LOW>,
+			     /* Hypervisor PPI */
+			     <1 10 IRQ_TYPE_LEVEL_LOW>;
The following form should be easier for read.

		interrupts = <1 13 IRQ_TYPE_LEVEL_LOW>, /* Physical Secure
PPI */
			     <1 14 IRQ_TYPE_LEVEL_LOW>, /* Physical Non-
Secure PPI */
			     <1 11 IRQ_TYPE_LEVEL_LOW>, /* Virtual PPI */
			     <1 10 IRQ_TYPE_LEVEL_LOW>; /* Hypervisor PPI
*/

Agreed. My bad. Will correct in v2

quoted
+	};
+
+	pmu {
+		compatible = "arm,armv8-pmuv3";
+		interrupts = <0 106 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	gic: interrupt-controller at 1400000 {
+		compatible = "arm,gic-400";
+		#interrupt-cells = <3>;
+		interrupt-controller;
+		reg = <0x0 0x1401000 0 0x1000>, /* GICD */
+		      <0x0 0x1402000 0 0x2000>, /* GICC */
+		      <0x0 0x1404000 0 0x2000>, /* GICH */
+		      <0x0 0x1406000 0 0x2000>; /* GICV */
+		interrupts = <1 9 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	reboot {
+		compatible = "syscon-reboot";
+		regmap = <&dcfg>;
+		offset = <0xb0>;
+		mask = <0x02>;
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		clockgen: clocking at 1ee1000 {
+			compatible = "fsl,ls1012a-clockgen";
+			reg = <0x0 0x1ee1000 0x0 0x1000>;
+			#clock-cells = <2>;
+			clocks = <&sysclk>;
+		};
+
+		scfg: scfg at 1570000 {
+			compatible = "fsl,ls1012a-scfg", "syscon";
+			reg = <0x0 0x1570000 0x0 0x10000>;
+			big-endian;
+		};
Please sort these nodes with unit-address in order of the address.

Shawn

quoted
+
+		dcfg: dcfg at 1ee0000 {
+			compatible = "fsl,ls1012a-dcfg",
+				     "syscon";
+			reg = <0x0 0x1ee0000 0x0 0x10000>;
+			big-endian;
+		};
+
+		i2c0: i2c at 2180000 {
+			compatible = "fsl,vf610-i2c";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0x2180000 0x0 0x10000>;
+			interrupts = <0 56 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&clockgen 4 0>;
+			status = "disabled";
+		};
+
+		i2c1: i2c at 2190000 {
+			compatible = "fsl,vf610-i2c";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0x2190000 0x0 0x10000>;
+			interrupts = <0 57 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&clockgen 4 0>;
+			status = "disabled";
+		};
+
+		duart0: serial at 21c0500 {
+			compatible = "fsl,ns16550", "ns16550a";
+			reg = <0x00 0x21c0500 0x0 0x100>;
+			interrupts = <0 54 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen 4 0>;
+		};
+
+		duart1: serial at 21c0600 {
+			compatible = "fsl,ns16550", "ns16550a";
+			reg = <0x00 0x21c0600 0x0 0x100>;
+			interrupts = <0 54 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen 4 0>;
+		};
+
+		gpio0: gpio at 2300000 {
+			compatible = "fsl,qoriq-gpio";
+			reg = <0x0 0x2300000 0x0 0x10000>;
+			interrupts = <0 66 IRQ_TYPE_LEVEL_LOW>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio1: gpio at 2310000 {
+			compatible = "fsl,qoriq-gpio";
+			reg = <0x0 0x2310000 0x0 0x10000>;
+			interrupts = <0 67 IRQ_TYPE_LEVEL_LOW>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		wdog0: wdog at 2ad0000 {
+			compatible = "fsl,ls1012a-wdt",
+				     "fsl,imx21-wdt";
+			reg = <0x0 0x2ad0000 0x0 0x10000>;
+			interrupts = <0 83 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&clockgen 4 0>;
+			big-endian;
+		};
+
+		sai1: sai at 2b50000 {
+			#sound-dai-cells = <0>;
+			compatible = "fsl,vf610-sai";
+			reg = <0x0 0x2b50000 0x0 0x10000>;
+			interrupts = <0 148 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&clockgen 4 3>, <&clockgen 4 3>,
+				 <&clockgen 4 3>, <&clockgen 4 3>;
+			clock-names = "bus", "mclk1", "mclk2", "mclk3";
+			dma-names = "tx", "rx";
+			dmas = <&edma0 1 47>,
+			       <&edma0 1 46>;
+			status = "disabled";
+		};
+
+		sai2: sai at 2b60000 {
+			#sound-dai-cells = <0>;
+			compatible = "fsl,vf610-sai";
+			reg = <0x0 0x2b60000 0x0 0x10000>;
+			interrupts = <0 149 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&clockgen 4 3>, <&clockgen 4 3>,
+				 <&clockgen 4 3>, <&clockgen 4 3>;
+			clock-names = "bus", "mclk1", "mclk2", "mclk3";
+			dma-names = "tx", "rx";
+			dmas = <&edma0 1 45>,
+			       <&edma0 1 44>;
+			status = "disabled";
+		};
+
+		edma0: edma at 2c00000 {
+			#dma-cells = <2>;
+			compatible = "fsl,vf610-edma";
+			reg = <0x0 0x2c00000 0x0 0x10000>,
+			      <0x0 0x2c10000 0x0 0x10000>,
+			      <0x0 0x2c20000 0x0 0x10000>;
+			interrupts = <0 103 IRQ_TYPE_LEVEL_LOW>,
+				     <0 103 IRQ_TYPE_LEVEL_LOW>;
+			interrupt-names = "edma-tx", "edma-err";
+			dma-channels = <32>;
+			big-endian;
+			clock-names = "dmamux0", "dmamux1";
+			clocks = <&clockgen 4 3>,
+				 <&clockgen 4 3>;
+		};
+
+		sata: sata at 3200000 {
+			compatible = "fsl,ls1012a-ahci";
+			reg = <0x0 0x3200000 0x0 0x10000>;
+			interrupts = <0 69 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&clockgen 4 0>;
+		};
+	};
+};
--
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel at lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel





  

    
RE: [PATCH] arm64: Add DTS support for FSL's LS1012A SoC

    

      From: Harninder Rai <hidden>

      Date: 2016-11-15 06:46:41 
    

  

  
-----Original Message-----
From: Harninder Rai
Sent: Tuesday, November 15, 2016 12:15 PM
To: 'Shawn Guo' <shawnguo@kernel.org>
Cc: devicetree at vger.kernel.org; robh+dt at kernel.org;
mark.rutland at arm.com; oss at buserror.net; Bhaskar U
[off-list ref]; linux-arm-kernel at lists.infradead.org
Subject: RE: [PATCH] arm64: Add DTS support for FSL's LS1012A SoC

quoted
quoted
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1043a-qds.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1043a-rdb.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1046a-qds.dtb
It seems that the patch is not generated against mainline kernel.  We
do not have fsl-ls1046a-qds.dtb target in mainline kernel.
You already clarified in the following mail :)

quoted
quoted
+
+	reg_1p8v: regulator at 0 {
Drop the unit-address from node name, and name it like regulator-1p8v.
Ok. Will take care in V2

quoted
quoted
+
+&duart0 {
Please sort labeled nodes alphabetically.
Ok Sure
quoted
quoted
+	status = "okay";
+};
+
+&sai2 {
+	status = "okay";
+};
<snip>
quoted
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+			     /* Physical Secure PPI */
+		interrupts = <1 13 IRQ_TYPE_LEVEL_LOW>,
+			     /* Physical Non-Secure PPI */
+			     <1 14 IRQ_TYPE_LEVEL_LOW>,
+			     /* Virtual PPI */
+			     <1 11 IRQ_TYPE_LEVEL_LOW>,
+			     /* Hypervisor PPI */
+			     <1 10 IRQ_TYPE_LEVEL_LOW>;
The following form should be easier for read.

		interrupts = <1 13 IRQ_TYPE_LEVEL_LOW>, /* Physical Secure
PPI */
quoted
			     <1 14 IRQ_TYPE_LEVEL_LOW>, /* Physical Non-
Secure PPI */
quoted
			     <1 11 IRQ_TYPE_LEVEL_LOW>, /* Virtual PPI */
			     <1 10 IRQ_TYPE_LEVEL_LOW>; /* Hypervisor PPI
*/
quoted
Agreed. My bad. Will correct in v2

quoted
quoted
+		scfg: scfg at 1570000 {
+			compatible = "fsl,ls1012a-scfg", "syscon";
+			reg = <0x0 0x1570000 0x0 0x10000>;
+			big-endian;
+		};
Please sort these nodes with unit-address in order of the address.
ok
quoted
Shawn




    
  

  
    

      

        Keyboard shortcuts
      

      

        
          
hback out one level

          
jnext message in thread

          
kprevious message in thread

          
ldrill in

          
Escclose help / fold thread tree

          
?toggle this help