Thread (44 messages) flat view 44 messages, 5 authors, 2016-09-05

[PATCH v8 15/18] ARM: STi: DT: STiH407: Add uniperif reader dt nodes

From: Lee Jones <hidden>
Date: 2016-08-30 10:00:12
Also in: dri-devel, linux-devicetree, linux-remoteproc, lkml

On Fri, 26 Aug 2016, Peter Griffin wrote:
quoted hunk ↗ jump to hunk
This patch adds the DT node for the uniperif reader
IP block found on STiH407 family silicon.

Signed-off-by: Arnaud Pouliquen <redacted>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
---
 arch/arm/boot/dts/stih407-family.dtsi | 26 ++++++++++++++++++++++++++
 1 file changed, 26 insertions(+)
diff --git a/arch/arm/boot/dts/stih407-family.dtsi b/arch/arm/boot/dts/stih407-family.dtsi
index d263c96..bdddf2c 100644
--- a/arch/arm/boot/dts/stih407-family.dtsi
+++ b/arch/arm/boot/dts/stih407-family.dtsi
@@ -956,5 +956,31 @@
 			st,version = <5>;
 			st,mode = "SPDIF";
 		};
+
+		sti_uni_reader0: sti-uni-reader at 0 {
+			compatible = "st,sti-uni-reader";
+			status = "disabled";
I find it's normally nicer to place the status of the node at the
bottom, separated by a '\n'.  There isn't a functional difference
admittedly, but it would be my preference, since it's not describing
the device per se.
+			#sound-dai-cells = <0>;
+			st,syscfg = <&syscfg_core>;
+			reg = <0x8D83000 0x158>;
We usually use lower-case for the address.

Since this has a 'reg' property, the '0' in the node name does not
look appropriate.
+			interrupts = <GIC_SPI 87 IRQ_TYPE_NONE>;
+			dmas = <&fdma0 5 0 1>;
+			dma-names = "rx";
+			dai-name = "Uni Reader #0 (PCM IN)";
Oooo, not seen something like this before.

If it does not already have one, it would require a DT Ack.
+			st,version = <3>;
This will likely need a DT Ack too.  We usually encode this sort of
information in the compatible string.
+		};
+
+		sti_uni_reader1: sti-uni-reader at 1 {
+			compatible = "st,sti-uni-reader";
+			status = "disabled";
+			#sound-dai-cells = <0>;
+			st,syscfg = <&syscfg_core>;
+			reg = <0x8D84000 0x158>;
+			interrupts = <GIC_SPI 88 IRQ_TYPE_NONE>;
+			dmas = <&fdma0 6 0 1>;
+			dma-names = "rx";
+			dai-name = "Uni Reader #1 (HDMI RX)";
+			st,version = <3>;
+		};
All as above.
 	};
 };
-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org ? Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
Keyboard shortcuts
hback out one level
jnext message in thread
kprevious message in thread
ldrill in
Escclose help / fold thread tree
?toggle this help