[PATCH v7 2/2] [media] atmel-isc: DT binding for Image Sensor Controller driver
From: Songjun Wu <hidden>
Date: 2016-07-29 08:07:36
Also in:
linux-devicetree, linux-media, lkml
Subsystem:
media input infrastructure (v4l/dvb), open firmware and flattened device tree bindings, the rest · Maintainers:
Mauro Carvalho Chehab, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Linus Torvalds
DT binding documentation for ISC driver. Signed-off-by: Songjun Wu <redacted> --- Changes in v7: None Changes in v6: - Add "iscck" and "gck" to clock-names. Changes in v5: - Add clock-output-names. Changes in v4: - Remove the isc clock nodes. Changes in v3: - Remove the 'atmel,sensor-preferred'. - Modify the isc clock node according to the Rob's remarks. Changes in v2: - Remove the unit address of the endpoint. - Add the unit address to the clock node. - Avoid using underscores in node names. - Drop the "0x" in the unit address of the i2c node. - Modify the description of 'atmel,sensor-preferred'. - Add the description for the ISC internal clock. .../devicetree/bindings/media/atmel-isc.txt | 65 ++++++++++++++++++++++ 1 file changed, 65 insertions(+) create mode 100644 Documentation/devicetree/bindings/media/atmel-isc.txt
diff --git a/Documentation/devicetree/bindings/media/atmel-isc.txt b/Documentation/devicetree/bindings/media/atmel-isc.txt
new file mode 100644
index 0000000..bbe0e87c
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/atmel-isc.txt@@ -0,0 +1,65 @@ +Atmel Image Sensor Controller (ISC) +---------------------------------------------- + +Required properties for ISC: +- compatible + Must be "atmel,sama5d2-isc". +- reg + Physical base address and length of the registers set for the device. +- interrupts + Should contain IRQ line for the ISC. +- clocks + List of clock specifiers, corresponding to entries in + the clock-names property; + Please refer to clock-bindings.txt. +- clock-names + Required elements: "hclock", "iscck", "gck". +- #clock-cells + Should be 0. +- clock-output-names + Should be "isc-mck". +- pinctrl-names, pinctrl-0 + Please refer to pinctrl-bindings.txt. + +ISC supports a single port node with parallel bus. It should contain one +'port' child node with child 'endpoint' node. Please refer to the bindings +defined in Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: +isc: isc at f0008000 { + compatible = "atmel,sama5d2-isc"; + reg = <0xf0008000 0x4000>; + interrupts = <46 IRQ_TYPE_LEVEL_HIGH 5>; + clocks = <&isc_clk>, <&iscck>, <&isc_gclk>; + clock-names = "hclock", "iscck", "gck"; + #clock-cells = <0>; + clock-output-names = "isc-mck"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_isc_base &pinctrl_isc_data_8bit &pinctrl_isc_data_9_10 &pinctrl_isc_data_11_12>; + + port { + isc_0: endpoint { + remote-endpoint = <&ov7740_0>; + hsync-active = <1>; + vsync-active = <0>; + pclk-sample = <1>; + }; + }; +}; + +i2c1: i2c at fc028000 { + ov7740: camera at 21 { + compatible = "ovti,ov7740"; + reg = <0x21>; + clocks = <&isc>; + clock-names = "xvclk"; + assigned-clocks = <&isc>; + assigned-clock-rates = <24000000>; + + port { + ov7740_0: endpoint { + remote-endpoint = <&isc_0>; + }; + }; + }; +};
--
2.7.4