[PATCH] ARM: dts: sun8i: Add dts file for inet86dz board

Hi,

On Mon, Jun 13, 2016 at 1:55 AM, Hans de Goede [off-list ref] wrote:

The inet86dz board is a board used in 7" tablets from various oems.

These tablets are a23 based 7" tablets featuring a 1024x600 LCD,
512MB RAM, 4G NAND, rtl8188etv usb wifi, gsl1680 touchschreen,
micro-sd slot, 3.5mm headphone jack and a micro-usb otg connector
which doubles as charging port.

This seems awfully similar to the sun8i-a23-q8-tablet, any reason
not to include that or sun8i-q8-common.dtsi?

Do we already have a driver for this? I don't see one in linux-next.

+               reg = <0x40>;
+               interrupt-parent = <&pio>;
+               interrupts = <1 5 IRQ_TYPE_EDGE_FALLING>; /* PB5 */
+               pinctrl-names = "default";
+               pinctrl-0 = <&ts_power_pin_inet86dz>;
+               power-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+               touchscreen-size-x = <960>;
+               touchscreen-size-y = <640>;
+               touchscreen-max-fingers = <5>;
+               touchscreen-fw-name = "silead/gsl1680-inet86dz.fw";
+       };
+};
+
+&i2c1 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&i2c1_pins_a>;
+       status = "okay";
+};
+
+&lradc {
+       vref-supply = <&reg_vcc3v0>;
+       status = "okay";
+
+       button at 200 {
+               label = "Volume Up";
+               linux,code = <KEY_VOLUMEUP>;
+               channel = <0>;
+               voltage = <200000>;
+       };
+
+       button at 400 {
+               label = "Volume Down";
+               linux,code = <KEY_VOLUMEDOWN>;
+               channel = <0>;
+               voltage = <400000>;
+       };
+};
+
+&mmc0 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_inet86dz>;
+       vmmc-supply = <&reg_dcdc1>;
+       bus-width = <4>;
+       cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
+       cd-inverted;
+       status = "okay";
+};
+
+&pio {
+       bl_en_pin_inet86dz: bl_en_pin at 0 {
+               allwinner,pins = "PH6";
+               allwinner,function = "gpio_in";
+               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+               allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+       };
+
+       mmc0_cd_pin_inet86dz: mmc0_cd_pin at 0 {
+               allwinner,pins = "PB4";
+               allwinner,function = "gpio_in";
+               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+               allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+       };
+
+       ts_power_pin_inet86dz: ts_power_pin at 0 {
+               allwinner,pins = "PH1";
+               allwinner,function = "gpio_out";
+               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+               allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+       };
+
+       usb0_id_detect_pin: usb0_id_detect_pin at 0 {
+               allwinner,pins = "PH8";
+               allwinner,function = "gpio_in";
+               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+               allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+       };
+};
+
+&pwm {
+       pinctrl-names = "default";
+       pinctrl-0 = <&pwm0_pins>;
+       status = "okay";
+};
+
+&r_rsb {
+       status = "okay";
+
+       axp22x: pmic at 3a3 {
+               compatible = "x-powers,axp223";
+               reg = <0x3a3>;
+               interrupt-parent = <&nmi_intc>;
+               interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+               eldoin-supply = <&reg_dcdc1>;

Adding a drivevbus-supply referencing vcc_5v0 so it doesn't
show 0V would be nice.

ChenYu

+               x-powers,drive-vbus-en;
+       };
+};
+
+&r_uart {
+       pinctrl-names = "default";
+       pinctrl-0 = <&r_uart_pins_a>;
+       status = "okay";
+};
+
+#include "axp22x.dtsi"
+
+&reg_aldo1 {
+       regulator-always-on;
+       regulator-min-microvolt = <3000000>;
+       regulator-max-microvolt = <3000000>;
+       regulator-name = "vcc-io";
+};
+
+&reg_aldo2 {
+       regulator-always-on;
+       regulator-min-microvolt = <2350000>;
+       regulator-max-microvolt = <2650000>;
+       regulator-name = "vdd-dll";
+};
+
+&reg_aldo3 {
+       regulator-always-on;
+       regulator-min-microvolt = <2700000>;
+       regulator-max-microvolt = <3300000>;
+       regulator-name = "vcc-pll-avcc";
+};
+
+&reg_dc1sw {
+       regulator-name = "vcc-lcd";
+};
+
+&reg_dc5ldo {
+       regulator-always-on;
+       regulator-min-microvolt = <900000>;
+       regulator-max-microvolt = <1400000>;
+       regulator-name = "vdd-cpus";
+};
+
+&reg_dcdc1 {
+       regulator-always-on;
+       regulator-min-microvolt = <3000000>;
+       regulator-max-microvolt = <3000000>;
+       regulator-name = "vcc-3v0";
+};
+
+&reg_dcdc2 {
+       regulator-always-on;
+       regulator-min-microvolt = <900000>;
+       regulator-max-microvolt = <1400000>;
+       regulator-name = "vdd-sys";
+};
+
+&reg_dcdc3 {
+       regulator-always-on;
+       regulator-min-microvolt = <900000>;
+       regulator-max-microvolt = <1400000>;
+       regulator-name = "vdd-cpu";
+};
+
+&reg_dcdc5 {
+       regulator-always-on;
+       regulator-min-microvolt = <1500000>;
+       regulator-max-microvolt = <1500000>;
+       regulator-name = "vcc-dram";
+};
+
+&reg_dldo1 {
+       regulator-min-microvolt = <3300000>;
+       regulator-max-microvolt = <3300000>;
+       regulator-name = "vcc-wifi";
+};
+
+&reg_drivevbus {
+       regulator-name = "usb0-vbus";
+       status = "okay";
+};
+
+&reg_rtc_ldo {
+       regulator-name = "vcc-rtc";
+};
+
+&simplefb_lcd {
+       vcc-lcd-supply = <&reg_dc1sw>;
+};
+
+&usb_otg {
+       dr_mode = "otg";
+       status = "okay";
+};
+
+&usb_power_supply {
+       status = "okay";
+};
+
+&usbphy {
+       pinctrl-names = "default";
+       pinctrl-0 = <&usb0_id_detect_pin>;
+       usb0_id_det-gpio = <&pio 7 8 GPIO_ACTIVE_HIGH>; /* PH8 */
+       usb0_vbus_power-supply = <&usb_power_supply>;
+       usb0_vbus-supply = <&reg_drivevbus>;
+       usb1_vbus-supply = <&reg_dldo1>;
+       status = "okay";
+};
--
2.7.4