It's possible that there are some reasons to turn the PHY on while the
clock is 0.  In this case we just won't wait for the DLL to lock.

This is a bit of a stopgap until we figure out exactly when we're
supposed to wait for the DLL to lock and when we're supposed to power
cycle the PHY.

Note: this patch should help with suspend/resume where the system will
try to turn the PHY back on when the clock is 0.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
---
 drivers/phy/phy-rockchip-emmc.c | 59 ++++++++++++++++++++++++++---------------
 1 file changed, 37 insertions(+), 22 deletions(-)

diff --git a/drivers/phy/phy-rockchip-emmc.c b/drivers/phy/phy-rockchip-emmc.c
index 9dce958233a0..a2aa6aca7dec 100644
--- a/drivers/phy/phy-rockchip-emmc.c
+++ b/drivers/phy/phy-rockchip-emmc.c

@@ -88,15 +88,36 @@ static int rockchip_emmc_phy_power(struct phy *phy, bool on_off)
 	unsigned int caldone;
 	unsigned int dllrdy;
 	unsigned int freqsel = PHYCTRL_FREQSEL_200M;
+	unsigned long rate;
 	unsigned long timeout;
 
-	if (rk_phy->emmcclk != NULL) {
-		unsigned long rate = clk_get_rate(rk_phy->emmcclk);
+	/*
+	 * Keep phyctrl_pdb and phyctrl_endll low to allow
+	 * initialization of CALIO state M/C DFFs
+	 */
+	regmap_write(rk_phy->reg_base,
+		     rk_phy->reg_offset + GRF_EMMCPHY_CON6,
+		     HIWORD_UPDATE(PHYCTRL_PDB_PWR_OFF,
+				   PHYCTRL_PDB_MASK,
+				   PHYCTRL_PDB_SHIFT));
+	regmap_write(rk_phy->reg_base,
+		     rk_phy->reg_offset + GRF_EMMCPHY_CON6,
+		     HIWORD_UPDATE(PHYCTRL_ENDLL_DISABLE,
+				   PHYCTRL_ENDLL_MASK,
+				   PHYCTRL_ENDLL_SHIFT));
+
+	/* Already finish power_off above */
+	if (on_off == PHYCTRL_PDB_PWR_OFF)
+		return 0;
+
+	rate = clk_get_rate(rk_phy->emmcclk);
+
+	if (rate != 0) {
 		unsigned long ideal_rate;
 		unsigned long diff;
 
 		switch (rate) {
-		case 0 ... 74999999:
+		case 1 ... 74999999:
 			ideal_rate = 50000000;
 			freqsel = PHYCTRL_FREQSEL_50M;
 			break;

@@ -127,25 +148,6 @@ static int rockchip_emmc_phy_power(struct phy *phy, bool on_off)
 	}
 
 	/*
-	 * Keep phyctrl_pdb and phyctrl_endll low to allow
-	 * initialization of CALIO state M/C DFFs
-	 */
-	regmap_write(rk_phy->reg_base,
-		     rk_phy->reg_offset + GRF_EMMCPHY_CON6,
-		     HIWORD_UPDATE(PHYCTRL_PDB_PWR_OFF,
-				   PHYCTRL_PDB_MASK,
-				   PHYCTRL_PDB_SHIFT));
-	regmap_write(rk_phy->reg_base,
-		     rk_phy->reg_offset + GRF_EMMCPHY_CON6,
-		     HIWORD_UPDATE(PHYCTRL_ENDLL_DISABLE,
-				   PHYCTRL_ENDLL_MASK,
-				   PHYCTRL_ENDLL_SHIFT));
-
-	/* Already finish power_off above */
-	if (on_off == PHYCTRL_PDB_PWR_OFF)
-		return 0;
-
-	/*
 	 * According to the user manual, calpad calibration
 	 * cycle takes more than 2us without the minimal recommended
 	 * value, so we may need a little margin here

@@ -183,6 +185,19 @@ static int rockchip_emmc_phy_power(struct phy *phy, bool on_off)
 		     HIWORD_UPDATE(PHYCTRL_ENDLL_ENABLE,
 				   PHYCTRL_ENDLL_MASK,
 				   PHYCTRL_ENDLL_SHIFT));
+
+	/*
+	 * We turned on the DLL even though the rate was 0 because we the
+	 * clock might be turned on later.  ...but we can't wait for the DLL
+	 * to lock when the rate is 0 because it will never lock with no
+	 * input clock.
+	 *
+	 * Technically we should be checking the lock later when the clock
+	 * is turned on, but for now we won't.
+	 */
+	if (rate == 0)
+		return 0;