Hi,

On Mon, May 30, 2016 at 08:30:13PM +0800, luoyi.ly at gmail.com wrote:

From: luoyi <redacted>

Add support for the Bananapi M1 Plus A20 development board from sinovoip.com.cn .
This board features 1G RAM, 2 USB A receptacles, 1 micro USB receptacle for
OTG, 1 micro USB receptacle for power, HDMI, sata, Gbit ethernet, ir receiver,
3.5 mm jack for stero sound out, on board microphone, 40 gpio pins and sdio wifi.

What is the difference between the M1+ and the M1?

The first part the label is the board name, in that case that would be
bananapi-m1-plus.

+			gpios = <&pio 7 25 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";

So that's the power led?

+		};
+
+		green {
+			label = "bananapi:green:usr";
+			gpios = <&pio 7 24 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";

We don't enforce any trigger by default.

+
+		};
+	};
+
+	reg_gmac_3v3: gmac-3v3 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gmac_power_pin_bananapi>;
+		regulator-name = "gmac-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <100000>;
+		enable-active-high;
+		gpio = <&pio 7 23 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_vmmc3: vmmc3 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&vmmc3_pin_bananapi>;
+		regulator-name = "vmmc3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&pio 7 22 GPIO_ACTIVE_HIGH>;
+	};

You can use reg_vcc3v3 from sunxi-common-regulators.dtsi.

+
+};
+
+&ahci {
+	status = "okay";
+};
+
+&codec {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};

Please order your nodes alphabetically.

+
+&gmac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac_pins_rgmii_a>;
+	phy = <&phy1>;
+	phy-mode = "rgmii";
+	phy-supply = <&reg_gmac_3v3>;
+	status = "okay";
+
+	phy1: ethernet-phy at 1 {
+		reg = <1>;
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
+
+	axp209: pmic at 34 {
+		compatible = "x-powers,axp209";
+		reg = <0x34>;
+		interrupt-parent = <&nmi_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+	};
+};
+
+&ir0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ir0_rx_pins_a>;
+	status = "okay";
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bananapi>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; /* PH10 */
+	cd-inverted;
+	status = "okay";
+};
+
+&mmc3 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc3_pins_a>;
+	vmmc-supply = <&reg_vmmc3>;
+	bus-width = <4>;
+	non-removable;
+	enable-sdio-wakeup;
+	status = "okay";
+
+	brcmf: bcrmf at 1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupt-parent = <&pio>;
+		interrupts = <7 15 IRQ_TYPE_LEVEL_LOW>; 
+		interrupt-names = "host-wake";
+	};
+
+};
+
+&mmc3_pins_a {
+    /* AP6210 requires pull-up */
+	allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+};
+
+&pio {
+	gmac_power_pin_bananapi: gmac_power_pin at 0 {
+		allwinner,pins = "PH23";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+
+	led_pins_bananapi: led_pins at 0 {
+		allwinner,pins = "PH24", "PG2";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+
+	mmc0_cd_pin_bananapi: mmc0_cd_pin at 0 {
+		allwinner,pins = "PH10";
+		allwinner,function = "gpio_in";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+	};
+
+	usb1_vbus_pin_bananapi: usb1_vbus_pin at 0 {
+		allwinner,pins = "PH0";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+
+	usb2_vbus_pin_bananapi: usb2_vbus_pin at 0 {
+		allwinner,pins = "PH1";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+
+	vmmc3_pin_bananapi: vmmc3_pin at 0 {
+		allwinner,pins = "PH22";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+};
+
+&reg_usb1_vbus {
+	pinctrl-0 = <&usb1_vbus_pin_bananapi>;
+	gpio = <&pio 7 0 GPIO_ACTIVE_HIGH>; /* PH0 */
+	status = "okay";
+};
+
+&reg_usb2_vbus {
+	pinctrl-0 = <&usb2_vbus_pin_bananapi>;
+	gpio = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_a>;
+	status = "okay";
+};
+
+&usbphy {
+	usb1_vbus-supply = <&reg_usb1_vbus>;
+	usb2_vbus-supply = <&reg_usb2_vbus>;
+	status = "okay";
+};
-- 
2.8.3

Thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20160530/da12d889/attachment.sig>