Hi Shawn

On Wed, Nov 18, 2015 at 4:10 PM, Michael Trimarchi
[off-list ref] wrote:

www.engicam.com/en/products/embedded/som/standard/i-core-rqs-m6s-dl-d-q

Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
---
I'm not quite sure how ethernet tuning parameter
are working in other setup and this seems the
correct way to use it

As you can see my way to connect the ethernet phy is different. I have
seen that most of the boards put all the tuning under fec but unfortunately
this does not work. I don't know if people check if their value are correctly
written to the phy.

+
+&fec {
+       pinctrl-names = "default";
+       pinctrl-0 = <&pinctrl_enet_3>;
+       phy-handle = <&eth_phy>;
+       phy-mode = "rgmii";
+       status = "okay";
+       mdio {
+               eth_phy: ethernet-phy {
+                       rxc-skew-ps = <1140>;
+                       txc-skew-ps = <1140>;
+                       txen-skew-ps = <600>;
+                       rxdv-skew-ps = <240>;
+                       rxd0-skew-ps = <420>;
+                       rxd1-skew-ps = <600>;
+                       rxd2-skew-ps = <420>;
+                       rxd3-skew-ps = <240>;
+                       txd0-skew-ps = <60>;
+                       txd1-skew-ps = <60>;
+                       txd2-skew-ps = <60>;
+                       txd3-skew-ps = <240>;
+               };
+       };
+};
+

Michael

+&i2c1 {
+       status = "okay";
+       clock-frequency = <100000>;
+       pinctrl-names = "default";
+       pinctrl-0 = <&pinctrl_i2c1_1>;
+};
+
+&i2c2 {
+       clock-frequency = <100000>;
+       pinctrl-names = "default";
+       pinctrl-0 = <&pinctrl_i2c2_2>;
+       status = "okay";
+};
+
+&i2c3 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&pinctrl_i2c3_4>;
+       status = "okay";
+};
+
+&pcie {
+       pinctrl-names = "default";
+       pinctrl-0 = <&pinctrl_pcie>;
+       reset-gpio = <&gpio3 29 GPIO_ACTIVE_LOW>;
+       status = "okay";
+};
+
+&ssi1 {
+       fsl,mode = "i2s-slave";
+       status = "okay";
+};
+
+&uart4 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&pinctrl_uart4_1>;
+       status = "okay";
+};
+
+&usbh1 {
+       vbus-supply = <&reg_usb_h1_vbus>;
+       disable-over-current;
+       clocks = <&clks IMX6QDL_CLK_USBOH3>;
+       status = "okay";
+};
+
+&usbotg {
+       vbus-supply = <&reg_usb_otg_vbus>;
+       pinctrl-names = "default";
+       pinctrl-0 = <&pinctrl_usbotg_2>;
+       disable-over-current;
+       status = "okay";
+};
+
+&usdhc1 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&pinctrl_usdhc1_1>;
+       no-1-8-v;
+       status = "okay";
+};
+
+&usdhc3 {
+       pinctrl-names = "default", "state_100mhz", "state_200mhz";
+       pinctrl-0 = <&pinctrl_usdhc3_2>;
+       pinctrl-1 = <&pinctrl_usdhc3_2_100mhz>;
+       pinctrl-2 = <&pinctrl_usdhc3_2_200mhz>;
+       vmcc-supply = <&reg_sd3_vmmc>;
+       cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+       bus-witdh=<4>;
+       no-1-8-v;
+       status = "okay";
+};
+
+&usdhc4 {
+       pinctrl-names = "default", "state_100mhz", "state_200mhz";
+       pinctrl-0 = <&pinctrl_usdhc4_1>;
+       pinctrl-1 = <&pinctrl_usdhc4_1_100mhz>;
+       pinctrl-2 = <&pinctrl_usdhc4_1_200mhz>;
+       vmcc-supply = <&reg_sd4_vmmc>;
+       bus-witdh=<8>;
+       no-1-8-v;
+       non-removable;
+       status = "okay";
+};
--
2.6.3

--
| Michael Nazzareno Trimarchi                     Amarula Solutions BV |
| COO  -  Founder                                      Cruquiuskade 47 |
| +31(0)851119172                                 Amsterdam 1018 AM NL |
|                  [`as] http://www.amarulasolutions.com               |

-- 
| Michael Nazzareno Trimarchi                     Amarula Solutions BV |
| COO  -  Founder                                      Cruquiuskade 47 |
| +31(0)851119172                                 Amsterdam 1018 AM NL |
|                  [`as] http://www.amarulasolutions.com               |