[PATCH v5 5/5] ARM: dts: TS-4800: add basic device tree
From: shawnguo@kernel.org (Shawn Guo)
Date: 2015-11-25 06:14:00
Also in:
linux-watchdog, lkml
On Tue, Nov 24, 2015 at 01:00:53PM -0500, Damien Riegel wrote:
This device tree adds support for TS-4800 by Technologic Systems. This board is based on MX51-babbage, but there are some subtle differences in the pins used, and there is an additional FPGA that is memory-mapped. More details here: http://wiki.embeddedarm.com/wiki/TS-4800 Signed-off-by: Damien Riegel <redacted> --- .../devicetree/bindings/arm/technologic.txt | 6 +
Please put binding doc into a separate patch, and have device tree maintainers and list on copy of that patch.
quoted hunk ↗ jump to hunk
arch/arm/boot/dts/Makefile | 3 +- arch/arm/boot/dts/imx51-ts4800.dts | 190 +++++++++++++++++++++ 3 files changed, 198 insertions(+), 1 deletion(-) create mode 100644 Documentation/devicetree/bindings/arm/technologic.txt create mode 100644 arch/arm/boot/dts/imx51-ts4800.dtsdiff --git a/Documentation/devicetree/bindings/arm/technologic.txt b/Documentation/devicetree/bindings/arm/technologic.txt new file mode 100644 index 0000000..8422988 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/technologic.txt@@ -0,0 +1,6 @@ +Technologic Systems Platforms Device Tree Bindings +-------------------------------------------------- + +TS-4800 board +Required root node properties: + - compatible = "technologic,imx51-ts4800", "fsl,imx51";diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index bb8fa02..41b9985 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile@@ -258,7 +258,8 @@ dtb-$(CONFIG_SOC_IMX51) += \ imx51-apf51dev.dtb \ imx51-babbage.dtb \ imx51-digi-connectcore-jsk.dtb \ - imx51-eukrea-mbimxsd51-baseboard.dtb + imx51-eukrea-mbimxsd51-baseboard.dtb \ + imx51-ts4800.dtb dtb-$(CONFIG_SOC_IMX53) += \ imx53-ard.dtb \ imx53-m53evk.dtb \diff --git a/arch/arm/boot/dts/imx51-ts4800.dts b/arch/arm/boot/dts/imx51-ts4800.dts new file mode 100644 index 0000000..fac2058 --- /dev/null +++ b/arch/arm/boot/dts/imx51-ts4800.dts@@ -0,0 +1,190 @@ +/* + * Copyright 2015 Savoir-faire Linux + * + * This device tree is based on imx51-babbage.dts + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +#include "imx51.dtsi" + +/ { + model = "Technologic Systems TS-4800"; + compatible = "technologic,imx51-ts4800", "fsl,imx51"; + + chosen { + stdout-path = &uart1; + }; + + memory { + reg = <0x90000000 0x10000000>; + }; + + soc { + fpga {
For node with 'reg' property, it should be named in form of name at unit-adderss.
+ compatible = "simple-bus";
+ reg = <0xb0000000 0x1d000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ syscon: syscon at b0010000 {
+ compatible = "syscon", "simple-mfd";
+ reg = <0xb0010000 0x3d>;
+ bus-width = <16>;
+
+ wdt at e {
+ compatible = "technologic,ts4800-wdt";
+ syscon = <&syscon 0xe>;
+ };
+ };
+ };
+ };
+
+ clocks {
+ ckih1 {
+ clock-frequency = <22579200>;
+ };
+
+ ckih2 {
+ clock-frequency = <24576000>;
+ };
+ };
+};
+
+&esdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_esdhc1>;
+ cd-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fec>;
+ phy-mode = "mii";
+ phy-reset-gpios = <&gpio2 14 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <1>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+
+ rtc: m41t00 at 68 {
+ compatible = "stm,m41t00";
+ reg = <0x68>;
+ };
+};We generally sort device nodes alphabetically expect pin controller. That said, &i2c2 should be put after &fec.
+
+
+&iomuxc {
+ imx51-ts4800 {With commit 5fcdf6a7ed95 (pinctrl: imx: Allow parsing DT without function nodes) in place, we should be able to save this level of node. Shawn
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX51_PAD_CSPI1_MISO__ECSPI1_MISO 0x185
+ MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI 0x185
+ MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK 0x185
+ MX51_PAD_CSPI1_SS0__GPIO4_24 0x85 /* CS0 */
+ >;
+ };
+
+ pinctrl_esdhc1: esdhc1grp {
+ fsl,pins = <
+ MX51_PAD_SD1_CMD__SD1_CMD 0x400020d5
+ MX51_PAD_SD1_CLK__SD1_CLK 0x20d5
+ MX51_PAD_SD1_DATA0__SD1_DATA0 0x20d5
+ MX51_PAD_SD1_DATA1__SD1_DATA1 0x20d5
+ MX51_PAD_SD1_DATA2__SD1_DATA2 0x20d5
+ MX51_PAD_SD1_DATA3__SD1_DATA3 0x20d5
+ MX51_PAD_GPIO1_0__GPIO1_0 0x100
+ MX51_PAD_GPIO1_1__GPIO1_1 0x100
+ >;
+ };
+
+ pinctrl_fec: fecgrp {
+ fsl,pins = <
+ MX51_PAD_EIM_EB2__FEC_MDIO 0x000001f5
+ MX51_PAD_EIM_EB3__FEC_RDATA1 0x00000085
+ MX51_PAD_EIM_CS2__FEC_RDATA2 0x00000085
+ MX51_PAD_EIM_CS3__FEC_RDATA3 0x00000085
+ MX51_PAD_EIM_CS4__FEC_RX_ER 0x00000180
+ MX51_PAD_EIM_CS5__FEC_CRS 0x00000180
+ MX51_PAD_DISP2_DAT10__FEC_COL 0x00000180
+ MX51_PAD_DISP2_DAT11__FEC_RX_CLK 0x00000180
+ MX51_PAD_DISP2_DAT14__FEC_RDATA0 0x00002180
+ MX51_PAD_DISP2_DAT15__FEC_TDATA0 0x00002004
+ MX51_PAD_NANDF_CS2__FEC_TX_ER 0x00002004
+ MX51_PAD_DI2_PIN2__FEC_MDC 0x00002004
+ MX51_PAD_DISP2_DAT6__FEC_TDATA1 0x00002004
+ MX51_PAD_DISP2_DAT7__FEC_TDATA2 0x00002004
+ MX51_PAD_DISP2_DAT8__FEC_TDATA3 0x00002004
+ MX51_PAD_DISP2_DAT9__FEC_TX_EN 0x00002004
+ MX51_PAD_DISP2_DAT13__FEC_TX_CLK 0x00002180
+ MX51_PAD_DISP2_DAT12__FEC_RX_DV 0x000020a4
+ MX51_PAD_EIM_A20__GPIO2_14 0x00000085 /* Phy Reset */
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX51_PAD_KEY_COL4__I2C2_SCL 0x400001ed
+ MX51_PAD_KEY_COL5__I2C2_SDA 0x400001ed
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX51_PAD_UART1_RXD__UART1_RXD 0x1c5
+ MX51_PAD_UART1_TXD__UART1_TXD 0x1c5
+ MX51_PAD_UART1_RTS__UART1_RTS 0x1c5
+ MX51_PAD_UART1_CTS__UART1_CTS 0x1c5
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX51_PAD_UART2_RXD__UART2_RXD 0x1c5
+ MX51_PAD_UART2_TXD__UART2_TXD 0x1c5
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX51_PAD_EIM_D25__UART3_RXD 0x1c5
+ MX51_PAD_EIM_D26__UART3_TXD 0x1c5
+ MX51_PAD_EIM_D27__UART3_RTS 0x1c5
+ MX51_PAD_EIM_D24__UART3_CTS 0x1c5
+ >;
+ };
+
+ };
+};
--
2.5.0