On Tue, 2015-05-26 at 14:33 +0200, Ulf Hansson wrote:

[...]

quoted

quoted

quoted

quoted

quoted

+{
+       unsigned long tmo = jiffies + msecs_to_jiffies(20);
+
+       while ((readl(host->base + SDC_STS) & SDC_STS_CMDBUSY)
+                       && time_before(jiffies, tmo))
+               continue;
+
+       if (readl(host->base + SDC_STS) & SDC_STS_CMDBUSY) {
+               dev_err(host->dev, "CMD bus busy detected\n");
+               host->error |= REQ_CMD_BUSY;
+               msdc_cmd_done(host, MSDC_INT_CMDTMO, mrq, cmd);
+               return false;
+       }
+
+       if (mmc_resp_type(cmd) == MMC_RSP_R1B || cmd->data) {
+               /* R1B or with data, should check SDCBUSY */
+               while (readl(host->base + SDC_STS) & SDC_STS_SDCBUSY)
+                       cpu_relax();
+       }

MSDC seems to be handling card busy detection in HW, right?

Do not have this ability, HW only know if CMD/DAT is low, but do not
have any interrupt for it,

I see, but doesn't the above polling mean that msdc will not propagate
the response until the card have stopped signal busy? That's what
MMC_CAP_WAIT_WHILE_BUSY shall be used for.

As you see, we only check the "busy state" BEFORE issue a R1B command or
with data command, but do not check if AFTER the request was done, that
would do not match the "MMC_CAP_WAIT_WHILE_BUSY"(eg. CMD5 to sleep)

Okay, fair enough. Still, I don't understand why you want to do that?

Below is the description of these 2 bits:
1	CMDBSY	CMDBUSY	SD Command line busy status
S/W should always read this bit to make sure the command line is not
busy before sending the next command. 
If the command is R1B or data read/write command, S/W should check
SDCBUSY bit too.
Note: When Auto command 12 is enabled, this bit will be asserted
immediately after SDC_CMD is written and de-asserted after auto-command
12 finishes.
1'b0: No transmission is going on CMD line on SD bus
1'b1: There exists transmission going on CMD line on SD bus
0	SDCBSY	SDCBUSY	SD controller busy status
1'b0: SD controller is idle
1'b1: SD controller is busy

quoted

In addition, about CMD5, I find that the suspend/resume flow of EMMC is
stranger in new kernel version, when suspend, it may issue CMD5 to enter
sleep mode, then power off MMC, but when resume, it will
re-initialization, So that why need do the redundant CMD5 in suspend ?

Both CMD0 and CMD5 are valid as wakeup commands.

To be able to use CMD5, the VCCQ regulator must be kept enabled in the
sleep state. That's when it becomes a bit tricky, due to the range of
different host drivers and SoCs for how VCCQ is managed.

To be safe we have chosen to use CMD0, since it works for *all* cases
no matter if VCCQ get gated or not.

Moreover, using CMD5 as the wakeup command would require added
complexity in the code dealing with suspend/resume. I don't think the
effort is worth it, at least until someone has proven that the resume
time is greatly decreased by using CMD5.

quoted

quoted

Perhaps you should remove the above polling, and rely on the MMC core
to poll with CMD13 instead?

before any read/write command, core will issue CMD13 to confirm card
status, here is just only do double confirm to avoid HW issue.

What HW issue and why do you need to double confirm? It seems strange.

Some fake SD card, even the CMD13 get card status is in transfer state,
but when we do read/write, the data0 was pull low.

By the way, do you think need do some spinlock protect in our code ?
I cannot find a good reason to use spin lock, it seems no need
it,although there will be many thread(mmcqd, mmcqd/0boot1,) and the irq
handler.

Kind regards
Uffe