[PATCH v15 2/5] dt-bindings: document Rockchip thermal
From: Caesar Wang <hidden>
Date: 2014-10-28 08:52:00
Also in:
linux-devicetree, linux-pm, lkml
Subsystem:
open firmware and flattened device tree bindings, the rest, thermal · Maintainers:
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Linus Torvalds, Rafael J. Wysocki, Daniel Lezcano
This add the necessary binding documentation for the thermal found on Rockchip SoCs Signed-off-by: zhaoyifeng <redacted> Signed-off-by: Caesar Wang <redacted> --- .../bindings/thermal/rockchip-thermal.txt | 62 ++++++++++++++++++++++ 1 file changed, 62 insertions(+) create mode 100644 Documentation/devicetree/bindings/thermal/rockchip-thermal.txt
diff --git a/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt b/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt
new file mode 100644
index 0000000..fc30e1b
--- /dev/null
+++ b/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt@@ -0,0 +1,62 @@ +* Temperature Sensor ADC (TSADC) on rockchip SoCs + +Required properties: +- compatible : "rockchip,rk3288-tsadc" +- reg : physical base address of the controller and length of memory mapped + region. +- interrupts : The interrupt number to the cpu. The interrupt specifier format + depends on the interrupt controller. +- clocks : Must contain an entry for each entry in clock-names. +- clock-names : Shall be "tsadc" for the converter-clock, and "apb_pclk" for + the peripheral clock. +- #thermal-sensor-cells : Should be 1. See ./thermal.txt for a description. +- hw-shut-temp : The hardware-controlled shutdown temperature value. +- tsadc-tshut-mode : The hardware-controlled shutdown mode 0:CRU 1:GPIO. +- tsadc-tshut-polarity : The hardware-controlled active polarity 0:LOW 1:HIGH. + +Exiample: +tsadc: tsadc at ff280000 { + compatible = "rockchip,rk3288-tsadc"; + reg = <0xff280000 0x100>; + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru SCLK_TSADC>, <&cru PCLK_TSADC>; + clock-names = "tsadc", "apb_pclk"; + pinctrl-names = "default"; + pinctrl-0 = <&otp_out>; + #thermal-sensor-cells = <1>; + hw-shut-temp = <125000>; + tsadc-tshut-mode = <0>; + tsadc-tshut-polarity = <0>; +}; + +Example: referring to thermal sensors: +thermal-zones { + cpu_thermal: cpu_thermal { + polling-delay-passive = <1000>; /* milliseconds */ + polling-delay = <5000>; /* milliseconds */ + + /* sensor ID */ + thermal-sensors = <&tsadc 1>; + + trips { + cpu_alert0: cpu_alert { + temperature = <80000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "passive"; + }; + cpu_crit: cpu_crit { + temperature = <120000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&cpu_alert0>; + cooling-device = + <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; +};
--
1.9.1