Hi,

i added linux-pm list.

Am 24.09.2014 23:47, schrieb Fabio Estevam:

On Wed, Sep 24, 2014 at 5:46 PM, Stefan Wahren [off-list ref] wrote:

quoted

thanks, registering cpufreq-cpu0 and adding missing properties reg & clocks
did the trick.

Now the sys interface of cpufreq is available and the mxs-regulator seems to
handle frequency change. But the frequency selection do not work as
expected. If i set cpu frequency to 454736, 392727 or 261818 kHz, the

Why 454736 instead of 454MHz? Same for the other values.

I took these values from the cpufreq driver in the Freescale BSP and 
they are in the datasheet, too. If i take 454000 and so one, i will get 
this nice oops:

root at duckbill:~# modprobe cpufreq-cpu0
[   95.764654] cpufreq: __cpufreq_add_dev: CPU0: Running at unlisted 
freq: 454736 KHz
[   95.773146] cpufreq_cpu0: failed to find OPP for 454736842
[   95.778692] cpufreq: __target_index: Failed to change cpu frequency: -34
[   95.786235] ------------[ cut here ]------------
[   95.790913] kernel BUG at drivers/cpufreq/cpufreq.c:1249!
[   95.796342] Internal error: Oops - BUG: 0 [#1] ARM
[   95.801154] Modules linked in: cpufreq_cpu0(+)
[   95.805673] CPU: 0 PID: 446 Comm: modprobe Not tainted 
3.17.0-rc4-00268-ge789d1c-dirty #17
[   95.813965] task: c6fa8980 ti: c6c86000 task.ti: c6c86000
[   95.819409] PC is at cpufreq_add_dev+0x530/0x5b4
[   95.824069] LR is at mark_held_locks+0x74/0x9c
[...]

quoted

cpufreq driver change it silently to 240000 kHz.

24MHz is the osc clock. It seems you did not turn on the PLL0.

Check the POWER bit of HW_CLKCTRL_PLL0CTRL0 register.

240000 kHz = 240 MHz

I fixed this specific problem by setting the clock reference in the DT 
to ref_cpu instead of cpu. After that i'm able to set 392727, 360000, 
261818 and 64000 kHz. Unfortunately the highest and default value 454736 
is not selectable:

[   38.901842] cpu cpu0: Looking up cpu0-supply from device tree
[   38.904082] freq_table: table entry 0: 64000 kHz
[   38.904141] freq_table: table entry 1: 261818 kHz
[   38.904176] freq_table: table entry 2: 360000 kHz
[   38.904206] freq_table: table entry 3: 392727 kHz
[   38.904235] freq_table: table entry 4: 454736 kHz
[   38.908050] freq_table: request for verification of policy (64000 - 
454736 kHz) for cpu 0
[   38.908116] freq_table: verification lead to (64000 - 454736 kHz) for 
cpu 0
[   38.908176] freq_table: request for verification of policy (64000 - 
454736 kHz) for cpu 0
[   38.908220] freq_table: verification lead to tage: vddd register val 30
root at duckbill:/sys/devices/system/cpu/cpu0/cpufreq# echo "454736" > 
scaling_setspeed
[  595.671708] cpufreq_cpu0: failed to find OPP for 454736842
[  595.677272] cpufreq: __target_index: Failed to change cpu frequency: -34

That looks like a bug in cpufreq.

Best regards
Stefan

PS: Here is my relevant DT:

############# imx28.dtsi

[...]

cpus {
	#address-cells = <1>;
	#size-cells = <0>;

	cpu at 0 {
		compatible = "arm,arm926ej-s";
		device_type = "cpu";
		reg = <0x0>;
		operating-points = <
			/* kHz	uV */
			454736  1550000
			392727  1475000
			360000  1375000
			261818  1275000
			64000   1050000
		>;
		clocks = <&clks 4>;
		clock-latency = <61036>; /* two CLK32 periods */
		cpu0-supply = <&reg_vddd>;
	};
};

[...]